Series LF1L, LF1XL Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 15,000 BTU/hr. They feature an all Lead Free* copper silicon alloy body with NPT threaded male inlet and NPT threaded female outlet connections, unique thermostat with special thermo-bonded coating, and test lever. Series LF1L, LF1XL are CSA listed. Model LF1L has 2 in. (50mm) thermostat and a test lever. Model LF1XL has an extension thermostat. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

100 Downloads

Series 957RPDA, 957NRPDDA, 957ZRPDA Reduced Pressure Detector Assemblies prevent the reverse flow of fire protection system substances from being pumped or siphoned into the potable water supply. The 957RPDA incorporates a meter to detect ground leaks and unauthorized illegal taps, greatly reducing annual water expenses. It consists of a compact, stainless steel body with stainless steel internal parts, two check valves, a pressure-differential relief valve, shutoff valves, torsion spring checks and relief valve, and bronze, nickel-plated test cocks. Series 957RPDA, 957NRPDDA, 957ZRPDA is 70% lighter than traditional designs and is ideal for health hazard cross-connection, such as on fire sprinkler systems. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

354 Downloads

Series ISCA-102-L/R Industry Standard single horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

53 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

39 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

34 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

29 Downloads

Series LFN223B, LFN223BS Lead Free* High Capacity Water Pressure Reducing Valves are used in commercial, industrial, and institutional applications to reduce incoming water pressure for protection of plumbing system components and to reduce water consumption. It consists of a triple-coated corrosion preventative Lead Free* cast copper silicon alloy body construction, an enlarged diaphragm, spring cage and seat orifice for super capacity performance, sealed spring cage for waterworks pit installations and thermal expansion bypass. Available with NPT threaded female inlet x NPT threaded female outlet with (LFN223BS) or without (LFN223B) strainer. Maximum Working Pressure: 300psi (21 bar), Adjustable Reduced Pressure Range: 25 to 75psi (172 to 517 kPa), Standard Pressure Setting: 50psi (345 kPa).

No Rating

Product Version: Revit MEP 2014

130 Downloads

Series ISCA-102-D Industry Standard back-to-back horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

69 Downloads

Series ISCA-122-D Industry Standard back-to-back vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

48 Downloads

Series ISCA-132-L/R/2 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, 4 in. (102mm) no hub side inlet(s), epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

39 Downloads

Series ISCA-132-D Industry Standard back-to-back vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, 4 in. (102mm) no hub side inlet(s), epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

54 Downloads

Series LF800M4FR Lead Free* Freeze Resistant Pressure Vacuum Breakers prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage. It consists of Lead Free* Cast Copper Silicon Alloy body construction, silicone rubber check valve disc, plastic check valve seat, stainless steel springs, a bonnet with silicone rubber O-ring seal, a lightweight plastic disc float, a built-in relief valve to protect the internal components and the body from freezing, tee handle or lever handle shutoffs, and test cocks for winterization draining. Series LF800M4FR is ideal in continuous pressure health hazard applications where exposure to sudden freezing conditions such as on irrigation systems and industrial process water systems can occur. Maximum Pressure: 150psi (10.3 bar), Minimum Pressure: 15psi (55kPa).

No Rating

Product Version: Revit MEP 2014

212 Downloads

Series LF40L, LF40XL Automatic Reseating Temperature and Pressure Relief Valves are used in commercial water heater applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters. They feature a Lead Free* brass body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, tamper-resistant bonnet screws, automatic reseating feature, and test lever. Model LF40L has a short thermostat for installation directly in available tank tapings. Model LF40XL has an extension thermostat for installation in the hot water outlet within the allowable distance from the top of the tank. Series LF40L, LF40XL valves are ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

173 Downloads

Series LFLL40XL, LFLLL40XL Extended Shank Automatic Reseating Temperature and Pressure Relief Valves are used in commercial water heater applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters. They feature an extended shank for installation on water heaters with extra thick insulation as well as a Lead Free* cast copper silicon alloy with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, tamper-resistant bonnet screws, automatic reseating feature, and test lever. Model LFLL40XL is available in sizes 3/4 and 1 in. (20 and 25mm). Model LFLLL40XL is available in size 3/4 (20mm) with an extra long extended shank. Series LFLL40L, LFLLL40XL valves are ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

89 Downloads

Series LFSL100XL, LFL100XL, LFLL100XL and LFLLL100XL Lead Free* Extended Shank Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 BTU/hr. They feature an extended shank for installation on water heaters with extra thick insulation as well as a Lead Free* brass body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, and a test lever. Model LFSL100XL is suitable for water heaters with up to 1-3/4 in. (45mm) of insulation. Model LFL100XL is suitable for water heaters with up to 2 in. (51mm) of insulation. Model LFLL100XL is suitable for water heaters with up to 2-1/2 in. (64mm) of insulation. Model LFLLL100XL is suitable for water heaters with up to 3 in. (76mm) of insulation. Series LFSL100XL, LFL100XL, LFLL100XL and LFLLL100XL are ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

90 Downloads

SPECIFICATIONS

• coverage Pattern
  
  90˚horizontal x 60˚ vertical
  
  


• operatingfrequency range
  
  50 Hz - 16 kHz +/-3dB
  
  


• continuous output
  
  133 dB SPL
  
  


• peak output
  
  139 dB SPL
  
  


• sensitivity
  
  101 dB (2.83 Volts into rated Z, at 1 meter) measured in free space
  
  


• driver complement
  
  four 15" woofers six 4" Mid Rangeone 1.4" High Freq
  
  


• dimensions
  
  26.5 x 45 x 25 inches
  
  


• weight
  
  215 lbs
  
  


• Rated Impedance
  
  8 Ohms
  
  


• Power Rating
  
  1400 Watts Continuos 2800 Watts Program
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/synergy-horn/sh-96/
  
  

No Rating

Product Version: Unknown

720 Downloads

SPECIFICATIONS

• coverage Pattern
  
  80Deg Conical
  
  


• operatingfrequency range
  
  113 Hz – 18 kHz +/- 3 dB70Hz – 19 kHz -10 dB
  
  


• continuous output
  
  127 dB SPL
  
  


• peak output
  
  133 dB SPL
  
  


• sensitivity
  
  101 dB (2.83 Volts into rated Z, at 1 meter) measured in free space
  
  


• driver complement
  
  one 12", one 1.4", coaxial
  
  


• dimensions
  
  32.25 x 26 x 14.5 inches
  
  


• weight
  
  51 Lbs.
  
  


• Rated Impedance
  
  8 ohms
  
  


• Power Rating
  
  400 watts Continuous, 1600 Watts Peak
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/outdoor-series/os80/#slide1
  
  

No Rating

Product Version: Unknown

278 Downloads

SPECIFICATIONS

• coverage Pattern
  
  140 x 10
  
  


• operatingfrequency range
  
  77 Hz – 15 kHz +/- 3 dB50Hz – 18 kHz -10 dB
  
  


• continuous output
  
  127 dBSPL
  
  


• peak output
  
  133 dBSPL
  
  


• sensitivity
  
  99 dBSPL measured at 10M @ 28.3V input
  
  


• driver complement
  
  Eight - 5” Coaxial drivers
  
  


• dimensions
  
  60”H x 9”W x 9”D
  
  


• weight
  
  100 lbs.
  
  


• Rated Impedance
  
  4 ohms
  
  


• Power Rating
  
  1300 watts continuous 5200 watts peak
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/sbh/sbh-10/
  
  

No Rating

Product Version: Unknown

863 Downloads

SPECIFICATIONS

• operatingfrequency range
  
  34 Hz- 300 Hz -3dB28 Hz - 400 Hz -10dB
  
  


• continuous output
  
  141 dB SPL
  
  


• peak output
  
  147 dB SPL
  
  


• sensitivity
  
  117 dB SPL (2.83 Volts into rated Z, at 1 meter) measured in half space
  
  


• driver complement
  
  two 18" long excursion woofers
  
  


• dimensions
  
  45 x 45 x 22.5 inches
  
  


• weight
  
  277 lbs
  
  


• Rated Impedance
  
  switchablea single 2 ohm loadortwo 4 ohm loads
  
  


• Power Rating
  
  3600 watts continuous 14,400 watt peak
  
  


• 
  
  http://www.danleysoundlabs.com/products/subwoofers/dbh/dbh218/
  
  

No Rating

Product Version: Unknown

209 Downloads

SPECIFICATIONS

• coverage Pattern
  
  80° Conical
  
  


• operatingfrequency range
  
  110Hz-22kHz
  
  


• continuous output
  
  128dB SPL
  
  


• peak output
  
  134dB SPL
  
  


• sensitivity
  
  102dB SPL
  
  


• driver complement
  
  1x12" coaxial
  
  


• dimensions
  
  25.5 x 24 x 12.75 inches
  
  


• weight
  
  65 lbs
  
  


• Rated Impedance
  
  8 Ohms
  
  


• Power Rating
  
  1600 Watts Peak
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/molded-synergy-horns/sm80/
  
  

No Rating

Product Version: Unknown

697 Downloads

SPECIFICATIONS

• coverage Pattern
  
  80° conical
  
  


• operatingfrequency range
  
  86Hz- 19KHz +/-3dB70Hz- 20KHz -10dB
  
  


• continuous output
  
  128dBSPL
  
  


• peak output
  
  134 dBSPL
  
  


• sensitivity
  
  102 dBSPL
  
  


• driver complement
  
  1-12”/1-1.4”HF coaxial
  
  


• dimensions
  
  25.5”H x 24”W x 12.75”D
  
  


• weight
  
  50 lbs.
  
  


• Rated Impedance
  
  8 ohms
  
  


• Power Rating
  
  1600 watts
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/molded-synergy-horns/sm80m/
  
  

No Rating

Product Version: Unknown

634 Downloads