 |
Scupper with extension to give a more decorative appearance than just a hole in the wall for drainage. Parametric size and material. Revit 2017. |
No Rating |
Product Version: Unknown
1849 Downloads
|
|
 |
Almost all of the shelf and its components are parametric.
NOTICE- the holes in the wall strip should be manually entered as the calculation parameter |
|
Product Version: Unknown
14540 Downloads
|
|
|
 |
Supply Diffuser can be placed on any surface. Floor, Wall, Cieling, ext. |
No Rating |
Product Version: Revit Architecture 2013
8356 Downloads
|
|
|
 |
Spine board with head blocks and straps. Generic model for hanging on a wall. Use offsets to configure height. |
|
Product Version: Revit Structure 2017
726 Downloads
|
|
|
 |
Wall hosted Full Pier for metal buildings / roll-up doors. Create a new family type for whatever height you need. |
|
Product Version: Revit Architecture 2008
2976 Downloads
|
|
|
 |
MIFAB® Series MC-62 floor mounted service sink carrier with two lacquered 2” x 1” x 1/8” thick structural steel uprights with 3” x 4 ½” welded steel feet, and lacquered cast iron fitting with no hub waste and vent connection (specify size of each). Complete with lacquered cast iron faceplate assembly, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors and polished chrome plated finishing cap nuts. |
No Rating |
Product Version: Unknown
27 Downloads
|
|
|
 |
Woven timber & steel balcony with variable wall offset - railing type only really works in 300mm increments |
|
Product Version: Unknown
19324 Downloads
|
|
|
 |
I'm pretty new on revit families. This is a little profile that you can attach to your wall as reveal to make it look like a corrugated metallic face.
Revit version: 2017 |
No Rating |
Product Version: Unknown
3993 Downloads
|
|
|
 |
Wall cabinet used to place wine glasses. |
|
Product Version: Revit Architecture 2015
14213 Downloads
|
|
|
 |
This is a basic precast concrete tilt up prop which is wall based |
No Rating |
Product Version: Unknown
783 Downloads
|
|
|
 |
Wall Mounted Code Blue Switch for hospital or healthcare communications |
No Rating |
Product Version: Revit Architecture 2009
3264 Downloads
|
|
|
 |
Wall-based family. Residential AC compressor unit. |
No Rating |
Product Version: Revit Architecture 2011
2349 Downloads
|
|
|
 |
Just a basic, simple wall-mounted door stop, done with Revit 2017. |
No Rating |
Product Version: Revit Architecture 2016
847 Downloads
|
|
|
 |
You can use it only after building a wall Its stick to the wall I hope you like it |
|
Product Version: Revit Architecture 2009
25839 Downloads
|
|
|
 |
This door is Revit 6.1 compatible only. The door is based on formulas from the Stanley catalog with added parameters to control the frame finish and offset from the wall face. |
No Rating |
Product Version: Unknown
5065 Downloads
|
|
|
 |
This creates a removable division between rooms via a half wall. Used in a custom bar / theater renovation. Static at this point, but hope to make it parametric in the future. |
|
Product Version: Revit Building 9.1
19803 Downloads
|
|
|
 |
Adjustable mounting and pole heights with both standard pole mount and wall mount types |
|
Product Version: Revit Architecture 2008
12378 Downloads
|
|
|
 |
Frosted glass panel with brass posts designed to set on top of partial height wall. Parameters for length, and post visibilty. |
|
Product Version: Revit Architecture 2008
9497 Downloads
|
|
|
 |
fairly basic rectangular swimming pool with no slopes. parameters are attatched to depth, width, length, wall and floor thicknesses etc.. and meterials. |
|
Product Version: Unknown
39492 Downloads
|
|
|
 |
A wall mounted extract fan for wetrooms, ultility and kitchens.
Based on a Vent Axia Lo-Carbon Centra dMEV Unit |
No Rating |
Product Version: Unknown
2574 Downloads
|
|
|
 |
I have not seen anything like this everywhere I have looked. Therefore I decide to make one. Full mesh parameters. I have also done a fence with pole using curtain wall family which I have not posted yet but you may request for it. |
|
Product Version: Unknown
2355 Downloads
|
|
|
 |
Contains 10', 20', 40' STD. and 40', 45' Hich Cube containers. These are not families or grouped. The walls will accept Revit doors and windows without the need to change wall profile. Created these as I could not find anything else. These are not perfect by any means, but they work. |
|
Product Version: Revit Architecture 2015
6867 Downloads
|
|
|
 |
A 4X20 wall of small lockers. Good for locker rooms, bowling alleys, theme parks, things like that. Almost 20 feet long and 5 feet tall. |
No Rating |
Product Version: Revit Architecture 2018
2104 Downloads
|
|
|
 |
Yes, another Flush Door. This one has both 2D and 3D swing control and it works! Also has setback from face of wall as an instance parameter, fine and coarse symbolic lines. |
|
Product Version: Unknown
2957 Downloads
|
|
|
 |
A simple exterior stile and rail raised panel shutter. Wall based, Adjusts for width, height and dist off floor. |
No Rating |
Product Version: Unknown
3584 Downloads
|
|
|
 |
In wall washer water/drain connection |
|
Product Version: Revit MEP 2014
1613 Downloads
|
|
|
 |
Wall based light, can be placed above a frame or painting, etc.
Revit 2012. |
|
Product Version: Unknown
76551 Downloads
|
|
|
 |
Russian Imperial Insignia, Wall mounted Size 2m |
No Rating |
Product Version: Revit Structure 2020
81 Downloads
|
|
|
 |
Window louver frame fixed onto the wall face. |
No Rating |
Product Version: Revit Architecture 2012
1439 Downloads
|
|
|
 |
This is a Wall Faced Log Canopy with lots of flexibility... |
No Rating |
Product Version: Revit Architecture 2015
3474 Downloads
|
|
|
Search