 |
These Indian style archtop framed windows are created as per actual elements in use.
Banarasi archtop framed Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc. Arch height is set to vary in a limit & same for window width as well.
2 Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers. Lower vent can be remove simply by setting lower lite ht to zero.
3.All shutters are provided with 2D & 3D swing. Window shutters are out swing as used in Indian culture.
4. use families after studdying the parameters. Window width is restricted as per actual use.It is better to handle the family after loading in project.
5. Any querry can be done on my phone number 91 9919640999 Welcome for further help. |
No Rating |
Product Version: Unknown
164 Downloads
|
|
 |
MIFAB® SUPER-MAX gravity grease interceptor has a limited lifetime warranty and is made in the U.S.A. out of seamless, rotationally molded High Density Polyethylene with 3/8” uniform wall thickness. Interceptor is designed for above or below ground installation and includes an adjustable lid system, sample port access, internal baffle, deep seal trap covered by lid, internal air relief by-pass, stainless steel calibrated orifice plate (internal flow control), base for support and floor level installation and 4″ no hub inlet and outlet connections. Steel encased composite lids provide a water / gas tight seal and have a minimum of 20,000 LB. load capacity – in accordance with the loading requirements of AASHTO H20. The high density polyethylene material is PE 3135 from Dow 9.39 with a density of 0.939 g/cm3. The -PDI model is tested and certified to the PDI G-101 Standard, 100 GPM flow rate. For indoor/outdoor use. |
No Rating |
Product Version: Unknown
291 Downloads
|
|
|
 |
Wall mounted vanity countertop with 4 sinks and drain pipe. Lines for ADA clearances shown in side view. |
No Rating |
Product Version: Revit Architecture 2008
10059 Downloads
|
|
|
 |
Wall mounted vanity countertop with 5 sinks and drain pipe. Lines for ADA clearances shown in side view. |
|
Product Version: Revit Architecture 2008
7287 Downloads
|
|
|
 |
Wall mounted vanity countertop with 3 sinks and drain pipe. Lines for ADA clearances shown in side view. |
|
Product Version: Revit Architecture 2008
13153 Downloads
|
|
|
 |
These Indian style archtop framed windows are created as per actual elements in use.
Banarasi archtop framed Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc. Arch height is set to vary in a limit & same for window width as well.
2 Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers. Lower vent can be remove simply by setting lower lite ht to zero.
3.All shutters are provided with 2D & 3D swing. Window shutters are out swing as used in Indian culture.
4. use families after studdying the parameters. Window width is restricted as per actual use.It is better to handle the family after loading in project.
5. Any querry can be done on my phone number 91 9919640999 Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
201 Downloads
|
|
|
 |
These Indian style archtop framed windows are created as per actual elements in use.
Banarasi archtop framed Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc. Arch height is set to vary in a limit & same for window width as well.
2 Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers. Lower vent can be remove simply by setting lower lite ht to zero.
3.All shutters are provided with 2D & 3D swing. Window shutters are out swing as used in Indian culture.
4. use families after studdying the parameters. Window width is restricted as per actual use.It is better to handle the family after loading in project.
5. Any querry can be done on my phone number 91 9919640999 Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
138 Downloads
|
|
|
 |
These Indian style archtop framed windows are created as per actual elements in use.
Banarasi archtop framed Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc. Arch height is set to vary in a limit & same for window width as well.
2 Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers. Lower vent can be remove simply by setting lower lite ht to zero.
3.All shutters are provided with 2D & 3D swing. Window shutters are out swing as used in Indian culture.
4. use families after studdying the parameters. Window width is restricted as per actual use.It is better to handle the family after loading in project.
5. Any querry can be done on my phone number 91 9919640999 Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
151 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
437 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
172 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
161 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
153 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
138 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
163 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
109 Downloads
|
|
|
 |
Price Industries Max Security Perforated Face Grille
Lattice and perforated security grilles reduce the risk of damage and disassembly associated with traditional grilles in secure areas. With minimum and maximum security options as well as a variety of mounting types, these grilles are suitable for supply and return applications.
Featuring all-welded construction and integral wall sleeves, the MSPG perforated face steel maximum security grille is one of the most popular security grilles styles in the industry. |
No Rating |
Product Version: Revit MEP 2020
93 Downloads
|
|
|
 |
The beautiful Voilà wall sconce featuring a glass shade. Varying interior and exterior surfaces result in an exciting juxtaposition of light and shadow. Parameters include options for 4 finishes. Manufactured by Holtkötter. |
|
Product Version: Revit Architecture 2011
12913 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
|
Product Version: Revit Architecture 2018
489 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
|
Product Version: Revit Architecture 2018
256 Downloads
|
|
|
 |
These Indian style door windows are created as per actual elements in use.
Banarasi Door & Windows
1 Wooden frames are created from wood log section per design of CPWD India. the design prevents plaster damage around door window frames when face flushed with wall face. Insert in frame may be removed by using insert=0. A chanel is made all aroun middle of frame to hold a perforated 6mm dia pipe to inject pest control liquidin it periodically, to protect door frame from termite etc.
2 Multiple door leaf shutters can be swipe to make a new door. Multy lite shutter can be utilise for one fully glazed panel to multy lite, simply by adjusting the vertical & horizontal numbers.
3 window frames are made from same log sections.
4. window shutters are multy lite shutters & number of lites can be set.
5. windows are marked by hor bay numbers, like 1A,1B, 2A, 3A etc.
6.All shutters are provided with 2D & 3D swing. Door shutters are inswing while window shutters are out swing as used in Indian culture.
7. use families after studdying the parameters. Window width is restricted as per actual use.
8. Any querry can be done on my phone number 91 9919640999
9. Welcome for further help. |
No Rating |
Product Version: Revit Architecture 2018
238 Downloads
|
|
|
 |
AGRV_GENM-SPCQ_FloodControlGate-Double_防水閘門-雙
Flood Control Gate in basement driveway entrance in Taiwan (Double swing) with DIM & Material parameters and dimension Guide
I also add a void box so you can easyly insert it in a wall
Visit our website AgileRevit.com for more families |
No Rating |
Product Version: Revit Architecture 2018
334 Downloads
|
|
|
 |
Janela tipo Máxim-ar para parede cortina.
Awning window for curtain wall. Parameters translation:
- Material moldura = frame material
- Material vidro = glass material
- Material puxador = handle material
- Espessura moldura = frame thickness
- Espessura vidro = glass thickness
Revit 2022 |
|
Product Version: Revit Structure 2020
92 Downloads
|
|
|
 |
This wall sconce features a modern rectangular form accented by an elegantly curved glass shade. Parameters include options for 4 finishes. Manufactured by Holtkötter. |
|
Product Version: Revit Architecture 2011
6055 Downloads
|
|
|
 |
This wall sconce features a modern rectangular form accented by an elegantly curved glass shade. Parameters include options for 4 finishes. Manufactured by Holtkötter. |
No Rating |
Product Version: Revit Architecture 2011
5567 Downloads
|
|
|
 |
AGRV_GENM-SPCQ_FloodControlGate-Single_防水閘門-單
Flood Control Gate in basement driveway entrance in Taiwan (Single Swing) with DIM & Material parameters and dimension Guide
I also add a void box so you can easyly insert it in a wall
Visit our website AgileRevit.com for more families |
No Rating |
Product Version: Revit Architecture 2018
329 Downloads
|
|
|
 |
The beautiful Voilà wall sconce featuring a glass shade. Varying interior and exterior surfaces result in an exciting juxtaposition of light and shadow. Parameters include options for 2 finishes. Manufactured by Holtkötter. |
|
Product Version: Revit Architecture 2011
15747 Downloads
|
|
|
 |
This door has the capability of having 2 to an infinite amount or door panels. There is a parameter allowing for you to change the distance of the door to the exterior side of the wall.
Hope it helps,
smh |
|
Product Version: Revit Architecture 2014
2050 Downloads
|
|
|
 |
AGRV-HRAL_SeriesC-Parapet-Metal & Glass Railing
# Parapet(Short wall) mounted railing
# rail support
We proivde 2 type of Railing in RVT : H120,H150
We also create a Baluster using the railing support familt, so you can place it manully.
Visit our website AgrvArchitect.com for more families
Because the rvt file is too big, so I put the file in here :
https://drive.google.com/file/d/1TIqQGfTZHJhLxvAHKhBZwEPG244N61jc/view?usp=sharing
|
No Rating |
Product Version: Revit Architecture 2018
920 Downloads
|
|
|
 |
Elegantly designed and streamlined, these wall sconces feature high-quality French glass and are equipped with a double-ended, tubular, halogen bulb. Parameters include options for 5 finishes and 15 glass options. Manufactured by Holtkötter. |
No Rating |
Product Version: Revit Architecture 2011
11524 Downloads
|
|
|
 |
Elegantly designed and streamlined, these wall sconces feature high-quality French glass and are equipped with a double-ended, tubular, halogen bulb. Parameters include options for 5 finishes and 15 glass options. Manufactured by Holtkötter. |
|
Product Version: Revit Architecture 2011
8589 Downloads
|
|
|
Search