MIFAB® Series MC-25 residential water closet carrier system with lacquered cast iron no hub fitting (specify size and style), lacquered cast iron faceplate, mounting hardware, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

50 Downloads

MIFAB Series C1460-S (select model number) lacquered cast iron cleanout with large access area, tapered thread plug and square (specify cover size, either 7” x 7” or 9” x 9”), smooth nickel bronze access panel with allen key screwsand anchor frame with mounting lugs.

No Rating

Product Version: Unknown

21 Downloads

MIFAB® Series MC-62 floor mounted service sink carrier with two lacquered 2” x 1” x 1/8” thick structural steel uprights with 3” x 4 ½” welded steel feet, and lacquered cast iron fitting with no hub waste and vent connection (specify size of each). Complete with lacquered cast iron faceplate assembly, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

24 Downloads

MIFAB® Series MC-21 floor mounted single, horizontal, adjustable, water closet carrier without fitting, 4” (102) back outlet waste connection (specify no hub or threaded), lacquered cast iron adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

25 Downloads

MIFAB Series MC-10D-EXT double, horizontal, adjustable high rough-in water closet carrier with lacquered cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

50 Downloads

MIFAB® Series MC-62 floor mounted service sink carrier with two lacquered 2” x 1” x 1/8” thick structural steel uprights with 3” x 4 ½” welded steel feet, and lacquered cast iron fitting with no hub waste and vent connection (specify size of each). Complete with lacquered cast iron faceplate assembly, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

63 Downloads

MIFAB® Series MC-12-HS single, vertical, adjustable, hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

38 Downloads

MIFAB® Series MC-12 single, vertical, adjustable, water closet carrier with lacquered cast iron fitting, 4” (102) no hub waste, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

49 Downloads

MIFAB® Series MC-12D-HS double, vertical, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

24 Downloads

MIFAB® Series MC-10-HS (Specify -L for left or -R for right design) single, horizontal, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

34 Downloads

MIFAB® Series MC-13-HS single, vertical, adjustable, hub and spigot water closet carrier with lacquered cast iron fitting, left, right or both (specify) 4” (102) side inlets, 2” (51) vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

22 Downloads

MIFAB® Series MC-15D double, vertical, fixed water closet carrier with offset lacquered cast iron fitting, 4” (102) no hub waste, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

42 Downloads

I have had this family in my library for many years now. I created this in Revit 2013 or 2014 originally.

 You can make this a tapered column or straight column frame by adjusting the A1 and B1 parameters.

It has worked very well for me however it could use some further automation in terms of adjustability in the project environment as well as additional flexibility for Column Top adjustment (ie. angle of Slope at top)

The version uploaded works with Revit 2019 and up. I have plans to further develop the family and will upload updated versions as I get them ready.

No Rating

Product Version: Revit Architecture 2019

1224 Downloads

MIFAB® Series MC-10D-27-37-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered, 37” (940) long barrel cast iron fitting, 2” (51) no hub vent connection, 2” (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

23 Downloads

MIFAB® Series MC-10D-27-37-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered, 37” (940) long barrel cast iron fitting, 2” (51) no hub vent connection, 2” (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

16 Downloads

MIFAB® Series MC-10-EXT (Specify L for left or R for right design) single, horizontal, adjustable, high rough-in water closet carrier with lacquered cast iron fitting, 4” (102) no hub waste, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support

No Rating

Product Version: Unknown

26 Downloads

MIFAB® Series MC-13D-HS double, vertical, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, left, right or both (specify) 4” (102) side inlets, 4” (102) no hub waste, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts.

No Rating

Product Version: Unknown

19 Downloads

MIFAB® Series MC-10-27-37 (Specify L for left or R for right design) single, horizontal, adjustable, water closet carrier with lacquered, 37” (940) long barrel cast iron fitting, 4” (102) no hub waste, 2” (51) no hub vent connection, 2” (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

20 Downloads

MIFAB® Series MC-15 single, vertical, fixed, water closet carrier with offset lacquered cast iron fitting, 4” (102) no hub waste, 2” (51) no hub vent  connection, lacquered cast iron faceplate, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.

No Rating

Product Version: Unknown

16 Downloads

MIFAB® Series MC-10D-HS double, horizontal, adjustable hub and spigot water closet carrier with lacquered cast iron fitting, 2” (51) no hub vent connection, lacquered cast iron gasketed adjustable faceplates, universal floor mounted cast iron foot supports, adjustable 8” tapered thread ABS nipples with integral test caps, neoprene bowl gaskets, hardware, threaded rod protectors and polished chrome plated finishing cap nuts. 

No Rating

Product Version: Unknown

17 Downloads

Please rate and comment, thanks!

Took a while to figure out how to get these to work properly.

The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.

The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.com

Cans be individually rotated in project.

!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!

Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).

The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.

You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.

I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.

Hope these are helpfull for you!

Product Version: Revit Architecture 2017

1078 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

Product Version: Revit Architecture 2017

711 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

571 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

459 Downloads

anchor tie down support.

No Rating

Product Version: Unknown

55 Downloads

Out of the box Revit Wide Flange family with spray on fireproofing added! After a long time of waiting to get to this, I finally did and decided to share because it seems unavailable anywhere else online. It appears to be a highly requested family throughout a lot of forums.

Parameters include, SOFP thickness, Visibility ON/OFF, & SOFP Realistic material. Family can be flexed and does not slow more complex framed structures significantly.

Visible in plan, 3D etc. Sections nicely as well. Great for wall firestopping & MEP coordination.

SOFP will adjust to any size beam selected and will also adjust to medium/fine detail level.

In order for this family to work properly, it’s imperative, the type catalog is located within the same folder as the family. I would suggest keeping them in the default directory together:

C:\ProgramData\Autodesk\RVT 2018\Libraries\US Imperial\Structural Framing\Steel

SOFP material JPG should be loaded into default materials directory as well:

C:\Program Files (x86)\Common Files\Autodesk Shared\Materials\Textures\3\Mats

Hope this is helpful and you enjoy for free! Family was created in RVT2018 but can be upgraded.

No Rating

Product Version: Revit Architecture 2018

852 Downloads

MINISTAGE ROUND SPOT

Art. S.1315W1 MODULES COB 3000K  220-240Vac 1225lm CRI 90 MacAdam step 3Rated luminaire luminous flux: 1040lmRated input power: 11.2WLuminaire efficacy: 93lm/WElectronic ballast  ON/OFF not dimmable CELUMINAIRE TYPEProjector. IP rating IP 66MATERIAL CHARACTERISTICSDie-cast EN AB-47100 aluminium housing with high corrosion resistance.Stone wash surface treatment prior to painting process. A4 grade Stainless Steel screws with 2,5-3% molybdenum content which increases the resistance against corrosion. Silicone gaskets. Painting Process : 3 Step Process1) Surface treatment with BONDERITE. A heavy metal free chemical surface treatment containing ceramic nano particles giving a cohesive, inorganic and highly dense protective coating. 2) PRE POLYMERIZATION a process of introducing an epoxy primer with excellent characteristics to the paint which also offers very high resistance to oxidation due to its Zinc content. 3) POLYMERIZATION a process with the application of polyester powder with high resistance against UV rays and harsh weather conditions. Resistance test protection for Marine applications for 1200h. Mechanical resistance IK 07LIGHTING PERFORMANCE99.98% pure aluminium reflectors, or with concentrating lenses: The sophisticated optics focuses the beam and makes the light comfortable by reducing the direct glare of the light source. Clear toughened glass. LOR -- INSTALLATION AND MAINTENANCEThe tempered front glass diffuser is fixed externally to the fitting through silicon resin, perfectly flush with the front ring. Water and dirt deposits that can disturb the lighting performance of the projector can easily flow away. WIRINGSupply 5m cable section type FEP/FEP + PCP (Microstage and Ministage) or FLAT (Stage and Megastage) sealed with B component epoxy resin, wired internally protected by silicon sheaths. Isolation: CLASS II . Available colours: Aluminium grey (cod.14), Anthracite grey (cod.24). Weight: 1.73 Kg Glow Wire test: --LED circuit included.REGISTERED DESIGN MICROSTAGE BLADE OF LIGHT PATENTED, REGISTERED DESIGNThis luminaire contains built-in LED modules. In case of damage or malfunction please contact the manufacturer to receive additional instructions on how to replace and relative spare parts to order. The LED modules cannot be handled in the luminaire by the end user.LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), where uniformity and quality of the light is 70,000 hours referred to L80 B10 Ta 25 ° C (50,000 hours referable to L80 B10 Ta 40°C). Lifespan of the luminaire > 50,000 hours at 40°C. Performance Ambient temperature Tq 25°C. Operating ambient temperature range is from -20°C to +50°C. Storage temperature range from -20°C to +60°C.

No Rating

Product Version: Revit Architecture 2018

2316 Downloads

Our Calm range is available fully upholstered, upholstered seat only or simply as a ply wood seat, finished in various colours. It's made from a one piece shell for ease of cleaning and is stackable to save space. It's available as a single seat and as a modular beam seating unit.

Pay us a visit at Knightsbridge Furniture

(Created in Revit 2014)

Product Version: Unknown

10143 Downloads

Our Polo range is available fully upholstered, upholstered seat only or simply as a ply wood seat, finished in various colours. It's made from a one piece shell for ease of cleaning and is stackable to save space. It's available as a single seat and as a modular beam seating unit.

Pay us a visit at Knightsbribge Furniture

(Created in Revit 2014)

Product Version: Unknown

5092 Downloads