Roterra type rainwater collectors are made from the environmentally friendly material polyethylene (PE) and are intended to be buried in the ground. 

Roterra 1400 rainwater collectors are available in sizes from 2,200 L to 3,300 L.

Revit Version 2023, 2024, 2025

Product Version: Unknown

150 Downloads

90 degree coupler to FM200 Tank.This is an approximation and my first attempt of sharing.

Product Version: Revit Architecture 2009

1321 Downloads

A basic water softening system consisting of a pump that can be turned  (on /off), softener canister, brine tank, whole house filter and valving.

Product Version: Revit Architecture 2017

7390 Downloads

Parametric Termic Sun Panels, water tank, degree elevation, ecc..

Product Version: Unknown

2244 Downloads

100% Revit built Forklift. Based on the DWG import by WWHub.

UPDATE: Updated the wheels, steering column, steering wheel (created by pacu2), and added a hydraulic tank behind the driver's seat.

Product Version: Revit Architecture 2009

28063 Downloads

My first up load

No host can place any location. It alway height 1 m from ref plan. In plan you will see as symbol but in section&3D view will see all tank. Please coment after used.

Product Version: Revit MEP 2010

11313 Downloads

RA2008 Drywell with Manhole cover, Parametric. Set the base level then the tank Height then the Neck legth for the manhole cover top. The Heights are instance perameters so you can drag it to the heights you need.

Product Version: Unknown

3287 Downloads

RA2008 Drywell with Manhole cover, Parametric. Set the base level then the tank Height then the Neck legth for the manhole cover top. The Heights are instance perameters so you can drag it to the heights you need.

No Rating

Product Version: Revit Architecture 2008

1898 Downloads

MIFAB® Series MI-E-O-HU__ sanitary powder epoxy coated inside and outside fabricated 10 gauge steel electronic oil interceptor.

Unit to include: sediment bucket with perforated baffle near inlet, deep seal trap covered by lid, sewer gas stopper, securing bolt(s), removable baffle assembly and cross bar, stainless steel calibrated orfice plate, internal air relief by-pass, adjustable automatic draw-off assembly, double vent connection on each side, and steel powder epoxy coated, non skid rectangular lid(s).

Product Version: Unknown

121 Downloads

Series LF40L, LF40XL Automatic Reseating Temperature and Pressure Relief Valves are used in commercial water heater applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters. They feature a Lead Free* brass body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, tamper-resistant bonnet screws, automatic reseating feature, and test lever. Model LF40L has a short thermostat for installation directly in available tank tapings. Model LF40XL has an extension thermostat for installation in the hot water outlet within the allowable distance from the top of the tank. Series LF40L, LF40XL valves are ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

173 Downloads

Filtrine Model ES-2-RF-IW - Remote in-wall chiller/purifier for serving chilled/purified water to (1) or (2) dispensers within 10-15'. (2) Gal. storage tank. Serves a population of (100), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

692 Downloads

Fully Parametric Square Water Tank Family.LxBxH & each Cell can adjust. No of Base I Beam & Concrete can change & on/off

Product Version: Revit MEP 2018

975 Downloads

Inodoro doméstico de tanque bajo / Residential water closet (with tank)

Más familias / more families: shop.a3d.es

Product Version: Revit Architecture 2012

8872 Downloads

Tower Flow Seperator package with pump, tank and panel. Electrical Panel was made by someone else and pump was also made using Solidworks by someone else.  

Product Version: Revit MEP 2018

2274 Downloads

Filtrine Model ES-6-RFC-IW - Remote in-wall recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-400' via recirculating drinking water loop. (6) Gal. storage tank. Serves a population of (300), (assuming 1 qt./day/person typical usage).

Product Version: Revit Architecture 2012

1189 Downloads

Filtrine Model ES-2-RFC-IW - Remote in-wall recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-100' via recirculating drinking water loop. (2) Gal. storage tank. Serves a population of (100), (assuming 1 qt./day/person typical usage).

Product Version: Revit Architecture 2012

1475 Downloads

Filtrine Model ES-4-RFC-IW - Remote in-wall recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-200' via recirculating drinking water loop. (4) Gal. storage tank. Serves a population of (200), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

751 Downloads

Filtrine Model ES-8-RFC-IW - Remote in-wall recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-400' via recirculating drinking water loop. (8) Gal. storage tank. Serves a population of (400), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

690 Downloads

Filtrine Model ES-6-RFC-FS - Remote free-standing recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-400' via recirculating drinking water loop. (6) Gal. storage tank. Serves a population of (300), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

921 Downloads

Filtrine Model ES-2-RFC-FS - Remote free-standing recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-100' via recirculating drinking water loop. (2) Gal. storage tank. Serves a population of (100), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

756 Downloads

Filtrine Model ES-4-RFC-FS - Remote free-standing recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-200' via recirculating drinking water loop. (4) Gal. storage tank. Serves a population of (200), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

567 Downloads

Filtrine Model ES-8-RFC-FS - Remote free-standing recirculating chiller/purifier for serving chilled/purified water to multiple dispensers within 10'-400' via recirculating drinking water loop. (8) Gal. storage tank. Serves a population of (400), (assuming 1 qt./day/person typical usage).

No Rating

Product Version: Revit Architecture 2012

692 Downloads

Water Tank INECA

700 lts.

Product Version: Revit Architecture 2012

3010 Downloads

Based upon The AquaClad® modular slimline tank made from Bluescope® steel.

Product Version: Revit Architecture 2014

1198 Downloads

Model LF10L Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 80,000 BTU/hr. They have a bronze body with NPT threaded male inlet and NPT threaded female outlet connections, unique thermostat with special thermo-bonded coating, and a test lever. Model LF10L is ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

215 Downloads

Series LF100XL Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 BTU/hr. They feature a Lead Free* copper alloy body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, and a test lever. Model LF100XL-8 is also available with 8 in. (200mm) extension thermostat. Series LF100XL is ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

124 Downloads

Series LF1L, LF1XL Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 15,000 BTU/hr. They feature an all Lead Free* copper silicon alloy body with NPT threaded male inlet and NPT threaded female outlet connections, unique thermostat with special thermo-bonded coating, and test lever. Series LF1L, LF1XL are CSA listed. Model LF1L has 2 in. (50mm) thermostat and a test lever. Model LF1XL has an extension thermostat. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

96 Downloads

Series LF1L, LF1XL Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 15,000 BTU/hr. They feature an all Lead Free* copper silicon alloy body with NPT threaded male inlet and NPT threaded female outlet connections, unique thermostat with special thermo-bonded coating, and test lever. Series LF1L, LF1XL are CSA listed. Model LF1L has 2 in. (50mm) thermostat and a test lever. Model LF1XL has an extension thermostat. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

117 Downloads

Series LF1L, LF1XL Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 15,000 BTU/hr. They feature an all Lead Free* copper silicon alloy body with NPT threaded male inlet and NPT threaded female outlet connections, unique thermostat with special thermo-bonded coating, and test lever. Series LF1L, LF1XL are CSA listed. Model LF1L has 2 in. (50mm) thermostat and a test lever. Model LF1XL has an extension thermostat. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

100 Downloads

Series LFSL100XL, LFL100XL, LFLL100XL and LFLLL100XL Lead Free* Extended Shank Temperature and Pressure Relief Valves are used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 BTU/hr. They feature an extended shank for installation on water heaters with extra thick insulation as well as a Lead Free* brass body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating, and a test lever. Model LFSL100XL is suitable for water heaters with up to 1-3/4 in. (45mm) of insulation. Model LFL100XL is suitable for water heaters with up to 2 in. (51mm) of insulation. Model LFLL100XL is suitable for water heaters with up to 2-1/2 in. (64mm) of insulation. Model LFLLL100XL is suitable for water heaters with up to 3 in. (76mm) of insulation. Series LFSL100XL, LFL100XL, LFLL100XL and LFLLL100XL are ASME rated and CSA listed. Temperature Relief: 210 degreeF (99 degreeC). Pressure Relief Range: 75 to 150psi (5.2 to 10.3 bar). Standard Pressure Settings: 75, 100, 125, or 150psi (5.27, 7.03, 8.79, or 10.55 bar).

No Rating

Product Version: Revit MEP 2014

90 Downloads