No matirials assigned.

Looking for obj importer with material support

No Rating

Product Version: Unknown

28 Downloads

You can change materials and Pipe dimensions, it has self iluminated logs inside.  

Product Version: Revit Architecture 2011

7286 Downloads

Series LF4001E Lead Free* Dielectric Unions feature a female iron pipe thread to solder connection. Compliant to American Society of Sanitary Engineering ASSE Standard 1079-2005. These unions are designed to be installed between pipe made from dissimilar metals to prevent accelerated corrosion and deterioration in the piping system due to galvanic and stray current. Maximum Pressure: 250psi (17.2 bar). Maximum Temperature: 180°F (82°C)

No Rating

Product Version: Revit MEP 2014

100 Downloads

Great cosmetic decoration in your room, please leave some support as it took a long time to make

Product Version: Revit Architecture 2018

48824 Downloads

No matirials assigned.

Looking for obj importer with material support

No Rating

Product Version: Unknown

116 Downloads

Pipe diameters are parametric, not material assigned, please rate and comment.

No Rating

Product Version: Revit Architecture 2013

958 Downloads

The pipe diameters are parametric

no materials assigned

No Rating

Product Version: Revit Architecture 2013

1552 Downloads

Pipe diameters are parametric, no materials assigned, please rate and comment.

No Rating

Product Version: Unknown

1840 Downloads

Series ISCA-102-L/R Industry Standard single horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

53 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

39 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

34 Downloads

Series ISCA-122 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

29 Downloads

Series ISCA-102-D Industry Standard back-to-back horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

69 Downloads

Series ISCA-122-D Industry Standard back-to-back vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

48 Downloads

Simple parametric rainwater pipe. 

Product Version: Revit Architecture 2014

5445 Downloads

Generic model. Dimensions and pipe connection sizes, locations, length etc. fully parametric. Adjust based on selection.

No Rating

Product Version: Revit MEP 2017

785 Downloads

Series ISCA-132-L/R/2 Industry Standard single vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, 4 in. (102mm) no hub side inlet(s), epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

39 Downloads

The object is fabricated to support ducts especially when wall mounted bracket is not relevant

No Rating

Product Version: Unknown

199 Downloads

Series ISCA-132-D Industry Standard back-to-back vertical adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, 4 in. (102mm) no hub side inlet(s), epoxy coated ductile iron compression seal faceplate assembly, epoxy coated ductile iron foot supports and rod support assembly adjustable for standard and wheelchair height, ductile iron rear anchor support, adjustable ABS nipple with integral test cap and neoprene bowl gasket, stainless steel support rods and hardware, and chrome plated cap nuts. Carrier complies with requirements of ASME A112.6.1M up to a 1000 lb. (454 kg.) static load. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Revit MEP 2014

54 Downloads

2x3x6' loom with just the wefts and support bars

Product Version: Revit Architecture 2020

824 Downloads

Parametric:

- support numbers

- overhang

Product Version: Revit Architecture 2009

11738 Downloads

PA speaker with length and support as parametric...!

With Annotation

Product Version: Revit MEP 2015

2775 Downloads

Wood frame stair with 100mm support beam

Product Version: Revit Architecture 2017

2036 Downloads

This is a partially-parametric recessed shelving unit - intended support system is walls built around it within the project.

Product Version: Revit Architecture 2011

8572 Downloads

Drip sight glass, Filter/Regulator and Oiler. Based on Nrogren Products. 3D fine and 2D medium and coarse representaion, 3/4" pipe connectors.

Product Version: Revit MEP 2010

3410 Downloads

Support bracket for linear counter

Product Version: Unknown

2261 Downloads

Standard toilet from Revit imperial library cut in half and connected with 2" copper pipe. To show appearance of a toilet like this in rendering.

Product Version: Revit Architecture 2010

33545 Downloads

HI GUYS WE ARE FROM SINGAPORE! WE HOPE TO CREATE COOL ITEMs THAT IS UNIQUE. ITEMs WE CREATED ARE MOSTLY MODERN ZEN. PLEASE SUPPORT US. :)

Product Version: Unknown

928 Downloads

Pipe sizes included are 4", 6", 8", 10", 12", 14" and 16".  Family is easy to update to add more sizes. 

No Rating

Product Version: Revit Architecture 2019

342 Downloads

Septic tank with two port also adding pipe network.

With you can continue to edit or update this model.

Product Version: Revit Architecture 2014

7268 Downloads