Series 757DCDA, 757NDCDA Double Check Detector Assemblies prevent the backflow of pollutants that are objectionable but not toxic, from entering into the potable water supply. Compact housings consist of two independently operating tri-link check valves, two shutoff valves, and four test cocks. They feature a stainless steel housing and sleeve and are 70% lighter than traditional designs. Series 757, 757N is designed for non-health hazard applications and may be installed under continuous pressure service to protect against both backpressure and backsiphonage. This Series is used primarily on fire sprinkler lines when it is necessary to monitor unauthorized use of water. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

569 Downloads

Series 9D Dual Check Valves with Intermediate Atmospheric Vent prevent the reverse flow of hot or cold polluted water from entering into the potable water supply. They have a brass body with stainless steel internal parts, integral strainer, and two durable, tight-sealing, rubber check valves. Series 9D is designed for continuous pressure, non-health hazard applications in smaller supply lines, such as laboratory equipment, processing tanks, sterilizers, dairy equipment, and specifically for boiler feed lines. Minimum Working Pressure: 25psi (172kPa), Maximum Working Pressure: 175psi (12.1 bar)

No Rating

Product Version: Revit MEP 2014

231 Downloads

Series 994 Reduced Pressure Zone Assemblies prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure. It consists of a stainless steel body construction with stainless steel internal parts. The bottom-mounted relief valve is located between the two check valves, making it suitable for installations against an outside wall. Series 994 has a compact design with a short lay length, ideal for retrofit installations. The 994 is designed for health hazard applications. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

238 Downloads

MIFAB® MI-LINT Series sanitary powder epoxy coated inside and outside fabricated 10 gauge steel lint interceptor with flow rate of 34-1536 gpm. Unit shall include: 1/2″ (13) thick fixed primary straining baffle with 3/8″ (10) holes and secondary 1/2″ (13) thick removable straining baffle with 3/8″ (10) holes, removable cross bar, securing bolt(s), stainless steel calibrated orifice plate, and steel powder epoxy coated non skid rectangular gasketed lid(s).

No Rating

Product Version: Unknown

52 Downloads

Model LF174A Boiler Pressure Relief Valves are Lead Free* cast copper silicon alloy body safety relief valves for pressure protection only of all types of hot water heating boiler equipment. Pressure range is 50 to 150psi (3 - 10 bar) with corresponding high ratings from 2,459,000 to 14,370,000 BTU/hr. Female inlet and outlet connections. Sizes: 3/4in. - 2in. (20 - 50mm). The LF174A features Lead Free* construction to comply with Lead Free* installation requirements. It resists corrosive water conditions, sticking, and freezing, and it prevents water and sediment from being trapped in the seat. It is designed for emergency safety relief and shall not be used as an operating control.

No Rating

Product Version: Revit MEP 2014

210 Downloads

Series LF7 Lead Free* Dual Check Valves prevent the reverse flow of polluted water from entering into the drinking water supply at the service entrance or at individual outlets. They have a Lead Free* cast copper silicon alloy body construction, two plastic replaceable check valves, and stainless steel springs. Series LF7 is designed for non-health hazard residential water system containment, continuous pressure applications. It is installed immediately downstream of the residential water meter, in a vertical or horizontal position. Check with local inspection authorities for installation requirements. Minimum Working Pressure: 10psi (69 kPa) Maximum Working Pressure: 150psi (10 bar).

No Rating

Product Version: Revit MEP 2014

149 Downloads

Series 152A Process Steam Pressure Regulators are used in commercial, industrial, and institutional applications to regulate steam pressure in autoclaves, steam tables/irons, vulcanizers and large capacity process services. They are highly sensitive to reduced pressure changes. They have an iron body construction with NPT threaded female inlet and outlet connections, stainless steel strainer, laminated metal diaphragm, and sensitivity adjustment feature for critical flow. Series 152A offers full volume with minimum pressure drop and in-line serviceability. It is ideal for use on sterilizers, process lines, testing fixtures, and oil lines. Tight seating Model 152A-T available for dead end and liquid services. Maximum Supply Pressure: Up to 200psi (13.8 bar).

No Rating

Product Version: Revit MEP 2014

300 Downloads

Series LF601 & LF601S Lead Free* cast copper silicon alloy Maxi-Flo Check Valves are used to prevent the effects of water hammer in the piping system. They feature a Lead Free* copper silicon alloy body, Viton disc, and integral copper silicon alloy seat. They have a low pressure drop and can be installed in a horizontal or vertical position. Model LF601 is available in sizes 1/4 to 1/2 in. (8 to 15mm) with threaded connections. Model LF601S is available in sizes 1/2 to 1 in. (15 to 25mm) with solder connections. Maximum Pressure: 250psi (17.24 bar) WOG non-shock @ 100°F (38°C).

No Rating

Product Version: Revit MEP 2014

125 Downloads

The LF8 Series Hose Connection Vacuum Breakers permit the attachment of portable hoses to hose thread faucets and prevent the reverse flow of polluted water into the potable water supply due to backsiphonage. They have a copper silicon alloy body construction, stainless steel working parts, and a rubber diaphragm and disc. The LF8 Series is ideal for inside or outside health hazard installations requiring non-continuous pressure such as service sinks, swimming pools, photo developing tanks, laundry tubs, wash racks, dairy barns, marinas, and general outside gardening uses. Check with local inspection authorities for installation requirements. Maximum Pressure:125psi (8.6 bar).

No Rating

Product Version: Revit MEP 2014

237 Downloads

Series LFN250 Iron Body Water Pressure Reducing Valves are designed to reduce incoming water pressure to a sensible level to protect plumbing system components and reduce water consumption. This series is suitable for water supply pressures up to 250psi (17.2 bar) and may be adjusted from 25 - 75psi(172 - 517 kPa). The standard setting is 50psi (345 kPa). All parts are quickly and easily serviceable without removing the valve from the line. The optional bypass feature permits the flow of water back through the valve into the main when pressures, due to thermal expansion on the outlet side of the valve, exceed the pressure in the main supply. The LFN250 features Lead Free* construction to comply with Lead Free* installation requirements.

No Rating

Product Version: Revit MEP 2014

405 Downloads

Series 909RPDA Reduced Pressure Detector Assemblies prevent the reverse flow of fire protection system substances from being pumped or siphoned into the potable water supply. The 909RPDA incorporates a meter to detect ground leaks and unauthorized illegal taps, greatly reducing annual water expenses. It consists of an epoxy-coated cast iron body with stainless steel trim, bronze gate valves, a pressure-differential relief valve, shutoff valves, and bronze ball-type test cocks. Series 909RPDA provides maximum flow at low pressure drop utilizing the "air-in/water-out" design principle for protection during emergency combined backsiphonage and backpressure conditions. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

642 Downloads

Series LF26A Lead Free* Small Pressure Regulators are used in small general purpose applications to regulate pressure in piping systems using water and No. 2 fuel oil. They have a Lead Free* brass body construction with NPT threaded female inlet and outlet connections, 1/4 in. two-way low-pressure gauge port, aluminum spring cage, Buna-N stainless steel disc, reinforced Buna-N diaphragm, and tee handle adjustment. Options include Viton trim and slotted adjusting screw. Strainers are recommended. Series LF26A has an oversized orifice and is ideal for use on beverage dispensing and paint spraying equipment, ice cube machines, humidifiers, drinking fountains, and other small process applications. Maximum Working Pressure: 300psi (21 bar).

No Rating

Product Version: Revit MEP 2014

187 Downloads

Series LF263A Lead Free* Small Pressure Regulators are used in small general purpose applications to regulate pressure in piping systems using water and No. 2 fuel oil. They have a Lead Free* brass body construction with NPT threaded female inlet and outlet connections, 1/4 in. three-way low-pressure gauge port, aluminum spring cage, Buna-N stainless steel disc, reinforced Buna-N diaphragm, and tee handle adjustment. Options include Viton trim and slotted adjusting screw. Strainers are recommended. Series LF263A has an oversized orifice and is ideal for use on beverage dispensing and paint spraying equipment, ice cube machines, humidifiers, drinking fountains, and other small process applications. Maximum Working Pressure: 300psi (21 bar).

No Rating

Product Version: Revit MEP 2014

122 Downloads

Series 994DCDA Reduced Pressure Detector Assemblies prevent the reverse flow of fire protection system substances from being pumped or siphoned into the potable water supply. The 994DCDA incorporates a meter to detect ground leaks and unauthorized illegal taps, greatly reducing annual water expenses. It consists of a stainless steel body, stainless steel internal parts, thermoplastic check valves and a bottom-mounted relief valve. Series 994DCDA is half the weight of competitive designs, and its short lay length makes installation and maintenance simple and easy. It is ideal for installation on fire protection systems. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar)

No Rating

Product Version: Revit MEP 2014

341 Downloads

MIFAB® Series MI-SD____ sanitary epoxy coated inside and outside fabricated 10 gauge steel sand interceptor. Unit shall include: removable cross bar, four 3" (76) threaded vent connections, solid straining baffles, stainless steel calibrated orfice plate, securing bolt(s), sediment bucket with perforated baffle beside inlet, deep seal trap, sewer gas stopper, internal air relief by-pass, and steel powder epoxy coated non skid rectangular gasketed lid(s).

Product Version: Unknown

215 Downloads

Series LF008PCQT Lead Free* Anti-Siphon, Spill-Resistant, Vacuum Breakers prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage on indoor point-of-use applications. They have a Lead Free* cast copper silicon alloy body construction, thermoplastic check and float assembly valve, stainless steel springs, tee handles, and a molded diaphragm separating the air inlet from the potable water supply to prevent spillage. Series LF008PCQT is ideal for indoor use on machines or equipment in general plumbing applications. Maximum Working Pressure: 150psi (10.34 bar), Minimum Working Pressure: 8psi (55.2 kPa).

No Rating

Product Version: Revit MEP 2014

185 Downloads

Series U009 Reduced Pressure Zone Assemblies prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure. They have a bronze body construction with a unique swivel union, two in-line independently operating check valves, a removable stainless-steel relief valve with captured springs and replaceable seat discs, four ball valve test cocks, and an air gap drain fitting. Their compact and space-saving design facilitates easy assembly and maintenance access. They are ideal for protection at health hazard cross-connections or for containment at the service line entrance. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

241 Downloads

Here is a file to have Door/Window/Gate schedule and associated door panels. the window was using door family template, the chain link fence was using curtain wall with gate.

Change Door tags:1. While placing the door, click “Tags” in the Option Bar,2. In “Loaded Tags And Symbols”, under “Doors” Category, click “Loaded Tags”, then, switch between “Door Tag-AAA”, and “Wdw Tag-AAA”.

To link parameters from a nested family to the host family you will need to do the following.1. Open the host family with the nested inserted.2. Click on the nested family.3. Click “Edit Type” in the Properties.4. The “Type Properties” window will be shown.5. Click the parameter that you want to associate with other parameter.6. Click the little button at the far right of the parameter line you want to change7. Select parameter out of list or click add parameter and recreate the parameter.When the parameter is linked there will be an (=) sign on the little button.

Make sure that the associated parameters are in the same Group, which means Text, or Dimension. If the parameter is a length, then it needs to have a value instead of 0’ 0”.

No Rating

Product Version: Revit Architecture 2015

1749 Downloads

Series SS009 Stainless Steel Reduced Pressure Zone Assemblies prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure. They have a stainless steel body construction, two stainless steel check valves, stainless steel check seats, hydraulically-operated relief valve, and stainless steel, vandal-resistant ball valve test cocks. Series SS009 is ideal in applications where the downstream liquid is of a composition where bronze material would be damaged or if it is desirable to eliminate trace elements of lead and copper. Series SS009 is ideal in industrial or plant applications, in medical/diagnostic equipment, in reverse osmosis systems, and for other health hazard piping systems. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar)

No Rating

Product Version: Revit MEP 2014

476 Downloads

AGRV_GENM-SPCQ_ParkingBarrierA_車道柵欄機A

StandAlone ParkingBarrier (Single Barrier bar)

Metric ParkingBarrier with DIM & Material parameters and dimension Guide 

No Rating

Product Version: Revit Architecture 2018

381 Downloads

AGRV_GENM-SPCQ_ParkingBarrierA_車道柵欄機A

StandAlone ParkingBarrier (Single Barrier bar)

Metric ParkingBarrier with DIM & Material parameters and dimension Guide 

No Rating

Product Version: Revit Architecture 2018

164 Downloads

MIFAB Series MI-RICE sanitary powder epoxy coated inside and outside fabricated 10 gauge steel rice interceptor with flow rate of _____(indicate). Unit shall include: ½”(13) thick fixed primary straining baffle with 1/4” (6.4) holes and secondary ½”(13) thick removable straining baffle with 1/4” (6.4) holes, removable cross bar , securing bolt(s), stainless steel calibrated orfice plate, and steel powder epoxy coated non skid rectangular gasketed lid(s).

No Rating

Product Version: Unknown

45 Downloads

AGRV_GENM-SPCQ_ParkingBarrierB_車道柵欄機B

StandAlone ParkingBarrier (Foldable Barrier bar)

Metric ParkingBarrier with DIM & Material parameters and dimension Guide 

No Rating

Product Version: Revit Architecture 2018

243 Downloads

Series 957RPDA, 957NRPDDA, 957ZRPDA Reduced Pressure Detector Assemblies prevent the reverse flow of fire protection system substances from being pumped or siphoned into the potable water supply. The 957RPDA incorporates a meter to detect ground leaks and unauthorized illegal taps, greatly reducing annual water expenses. It consists of a compact, stainless steel body with stainless steel internal parts, two check valves, a pressure-differential relief valve, shutoff valves, torsion spring checks and relief valve, and bronze, nickel-plated test cocks. Series 957RPDA, 957NRPDDA, 957ZRPDA is 70% lighter than traditional designs and is ideal for health hazard cross-connection, such as on fire sprinkler systems. Check with local water authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

355 Downloads

Series LFN223B, LFN223BS Lead Free* High Capacity Water Pressure Reducing Valves are used in commercial, industrial, and institutional applications to reduce incoming water pressure for protection of plumbing system components and to reduce water consumption. It consists of a triple-coated corrosion preventative Lead Free* cast copper silicon alloy body construction, an enlarged diaphragm, spring cage and seat orifice for super capacity performance, sealed spring cage for waterworks pit installations and thermal expansion bypass. Available with NPT threaded female inlet x NPT threaded female outlet with (LFN223BS) or without (LFN223B) strainer. Maximum Working Pressure: 300psi (21 bar), Adjustable Reduced Pressure Range: 25 to 75psi (172 to 517 kPa), Standard Pressure Setting: 50psi (345 kPa).

No Rating

Product Version: Revit MEP 2014

131 Downloads

Series LFU009 Reduced Pressure Zone Assemblies are designed to protect potable water supplies in accordance with national plumbing codes and water authority requirements. The swivel feature in the series allows for it to be used in a variety of installations, including the prevention of health hazard cross-connections in piping systems or for containment at the service line entrance. This series features two in-line, independent check valves, captured springs, and replaceable check seats with an intermediate relief valve. Its compact modular design facilitates easy maintenance and assembly access. Sizes 1/2in. - 1in. (15 - 25mm) shutoffs have tee handles. It has cast copper silicon alloy body construction for durability. The LFU009 features Lead Free* construction to comply with Lead Free* installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

174 Downloads

MIFAB® Series XL-MI-G ____ sanitary, acid resistant, epoxy coated inside and outside fabricated 10 gauge steel hydro mechanical grease interceptor with flow rating of ____ (indicate) and grease holding capacity of ____ (indicate). Unit shall include: removable (fixed for XL-MI-G-10/-11) baffle assembly and cross bar, deep seal trap covered by lid, sewer gas stopper, securing bolt(s), stainless steel calibrated orfice plate, internal air relief by-pass, and steel acid resistant, powder epoxy coated, non skid, rectangular gasketed lid(s).

No Rating

Product Version: Unknown

336 Downloads

MIFAB® Series MI-FISH sanitary powder epoxy coated inside and outside fabricated 10 gauge steel fish scale interceptor. Unit shall include: Sediment bucket with perforated baffle near inlet (3/8” (9) holes), primary removable straining baffle (1/2” (13) thick with 1/4” (6) holes), secondary removable straining baffle (1/2” (13) thick with 1/8” (3) holes), securing bolt(s), removable cross bar, stainless steel calibrated orfice plate and steel powder epoxy coated non skid rectangular gasketed lid(s).

No Rating

Product Version: Unknown

111 Downloads

Series LF800M4FR Lead Free* Freeze Resistant Pressure Vacuum Breakers prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage. It consists of Lead Free* Cast Copper Silicon Alloy body construction, silicone rubber check valve disc, plastic check valve seat, stainless steel springs, a bonnet with silicone rubber O-ring seal, a lightweight plastic disc float, a built-in relief valve to protect the internal components and the body from freezing, tee handle or lever handle shutoffs, and test cocks for winterization draining. Series LF800M4FR is ideal in continuous pressure health hazard applications where exposure to sudden freezing conditions such as on irrigation systems and industrial process water systems can occur. Maximum Pressure: 150psi (10.3 bar), Minimum Pressure: 15psi (55kPa).

No Rating

Product Version: Revit MEP 2014

213 Downloads

MIFAB® Series MI-O-HU ____ sanitary powder epoxy coated inside and outside fabricated 10 gauge steel oil interceptor. Unit to include: sediment bucket with perforated baffle near inlet, deep seal trap covered by lid, sewer gas stopper, securing bolt(s), removable baffle assembly and cross bar, stainless steel calibrated orfice plate, internal air relief by-pass, adjustable automatic draw-off assembly, double vent connection on each side, and steel powder epoxy coated, non skid rectangular lid(s). Unit comes complete with integral holding tank for additional waste oil storage.

No Rating

Product Version: Unknown

279 Downloads