Hey Guys, here is a eyeglass case to add that extra detail to your renderings. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Not Parametric, it is the exact size of the case found in the stores. Please rate and leave a comment and let me know what you all think and if its helping?

Product Version: Unknown

368 Downloads

Parametric well made of precast concrete rings with 2 exits. You need also to load the manhole steal cover. It's a floor family, the manhole steal cover perforates the pavement.

Pou paramètric fet d'anelles de formigó prefabricat, amb con de reducció. Cal posar la profunditat de la cota d'aigua, i el nomebre d'anelles s'ajusta per tempteig. Connexions de clavegueram a banda i banda. És un element de terra, perfora el terra. S'ha de carregar també l'arxiu que és la tapa.

Pozo paramétrico de saneamiento hecho de anillas de hormigón prefabricado, con su cono de reducción. Hay que poner la cota de agua, y el número de anillas se coloca por tanteo. 2 Conexiones de saneamiento alineadas. Es un elemento de suelo, perfora el pavimento. Hay que cargar también el elemento que es la tapa del pozo.

Product Version: Unknown

4040 Downloads

Here is a weight watchers bathroom scale to add that extra detail to your renderings. With its smooth sleek look it will add a contemporary touch to any bath decor. Materials are listed under Scale for an easy change to any material or color that you would like. Not Parametric, it's the exact size of the scale. Let me know what you all think and if its helping?

Product Version: Revit Architecture 2017

1537 Downloads

Hey Guys, here is a Bamboo Kitchen Cutting Board to add that extra detail to your renderings. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Parametric, but it is currently 1' 6" long, 1' 0" wide and 3/4" tall. Please rate and leave a comment and let me know what you all think and if its helping?

Product Version: Unknown

4558 Downloads

Hey Guys, here is just a Bowling Pin that you can use for decoration or to put in a bowling alley. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Not Parametric, it's the exact size for USBC standards. Please rate and leave a comment. 

Product Version: Revit Architecture 2018

1922 Downloads

Hey Guys, here is just a Bowling Ball that you can use for decoration or to put in a bowling alley. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Has two layers an interior and exterior that can be customized to your liking. Not Parametric, it's the exact size for USBC standards. Please rate and leave a comment. 

Product Version: Revit Architecture 2018

2155 Downloads

I took the component below and made it parametric...

Product Version: Revit Architecture 2009

Uploaded By: JLinkUploaded On: Wed, Nov 4, 2009

No Rating

Product Version: Revit Architecture 2016

5496 Downloads

Parametric material.

Model made after corner bathtub "Niagara" from "AEssel"

1400x1400 mm.

It was created in Revit 2013, later was renewed to 2015 version.

Product Version: Unknown

8443 Downloads

An induction hot plate modeled loosely on Duxtop's. Not parametric.

2.5" high, 11.5" wide, 13" deep.

Control panel decal not included with family.

Meant to sit on top of a countertop and act like a mini portable stove. Enjoy!

No Rating

Product Version: Unknown

926 Downloads

Hey Guys, here is a pac man machine that you can use for decoration or for an arcade. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Not Parametric, it's the exact size of the machine that you would buy. Front lenght is 2'1", side width is 2'7" and it is 5'7" tall. Please rate and leave a comment and let me know what you think.

Product Version: Revit Architecture 2018

13361 Downloads

Hey Guys, here is a American Crew Hair Cream to add that extra detail to your renderings. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Not Parametric, it is the exact size of the bottle in the stores. Please rate and leave a comment and let me know what you all think and if its helping?

Product Version: Revit Architecture 2018

1840 Downloads

A sliding archive system shelves, for hunging big formats (like A0 sheets), brought from real life to digital world, by looking a manufactured unit by the paraguayan company Felipe Aghemo.

The parts have standart 3105xmm lenght, 900mm or 1350mm width, and 2170mm height; but the composition and materials are fully parametric.

Manufactered by Felipe Aghemo. Country: Paraguay.

Modeled by dufb. Country: Brazil.

============

Um sistema de prateleias/arquivos deslizantes, para pendurar grandes formatos (do tipo A0), trazido da vida real para o mundo digital, a partir de produto fabricado pela empresa paraguaia Felipe Aghemo.

Os módulos tem tamanho padrão de 3105xmm (altura), 900mm ou 1350mm (largura), e 2170mm (altura); mas a composição de quantidades de módulos e materiais de acabamento são inteiramente parametrizados.

Fabricado por Felipe Aghemo. País: Paraguai.

Modelado por dufb. País: Brazil.

No Rating

Product Version: Revit Structure 2017

1182 Downloads

A sliding archive system of shelves for small formats (like A3, A4) and/or books, brought from real life to digital world, measured from a manufactured unit by the paraguayan company Felipe Aghemo.

The parts have standart 3180xmm lenght, 403 or 767mm width, and 2240mm height. The composition and materials are fully parametric.

Manufactered by Felipe Aghemo. Country: Paraguay.

Modeled by dufb. Country: Brazil.

============

Um sistema de arquivos deslizantes, com prateleiras para pequeno formatos (A3, A4) e/ou livros, trazido da vida real para o mundo digital, a partir de produto fabricado pela empresa paraguaia Felipe Aghemo.

Os módulos têm tamanho padrão de 3180xmm (comprimento), 403 ou 767mm (largura), e 2240mm (altura). A composição de quantidades de módulos e materiais de acabamento são inteiramente parametrizados.

Fabricado por Felipe Aghemo. País: Paraguai.

Modelado por dufb. País: Brazil.

Product Version: Revit Architecture 2017

1549 Downloads

Hey Guys, here is a nice decorative kids desk to add that extra detail to your renderings. Materials are listed under properties tab in the edit type section for an easy change to any material or color that you would like. Not parametric, its current size is...

Width = 3' 4" Depth = 1' 6" Height = 2' 6"

Please leave a comment and let me know what you all think and if its helping?

Product Version: Unknown

3327 Downloads

Hey Guys, here is a nice decorative kids desk to add that extra detail to your renderings. Materials are listed under properties tab in the edit type section for an easy change to any material or color that you would like. Not parametric, its current size is...

Width = 5' 9" Depth = 1' 11" Height = 2' 6"

Please leave a comment and let me know what you all think and if its helping?

Product Version: Unknown

2411 Downloads

Please rate and comment, thanks!

Took a while to figure out how to get these to work properly.

The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.

The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.com

Cans be individually rotated in project.

!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!

Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).

The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.

You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.

I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.

Hope these are helpfull for you!

Product Version: Revit Architecture 2017

1090 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

Product Version: Revit Architecture 2017

720 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

606 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

479 Downloads

Parametric Sq wall opening with swapable fill Patterns and with or without Trim. 10 patterns to choose from. all parts of patterns are auto adjusted according to sq size 100mm to thousans of mm. Materials of diff patterns & Trim can be selected independently. Patterns can be off for clear Sq opening. O pattern is extra in front of main pattern, which can be off if not req. Array of thes openings By Er.L.J.Upadhyay +919919640999q

No Rating

Product Version: Revit Architecture 2018

108 Downloads

Hey Guys, here is a lovely Bathroom vanity to add that extra detail to your renderings. Materials are listed under the properties tab in the edit type section for an easy change to any material or color that you would like. The faucet I used was uploaded by thafera, so thank him for that awesome family. Not Parametric, it's 5' 7" long 1' 11" wide and 2' 11.5" tall from floor to top of countertop. Please leave a comment and let me know what you all think and if its helping?

Product Version: Revit Architecture 2017

21903 Downloads

DECORATIVE GLASS BASE & WOODEN SPHERES Materials for the base and the spheres can be changed.Created in RAC2009/Mental Ray materialsNot an AutoCAD import / not parametric but modifiable

Product Version: Revit Architecture 2009

20837 Downloads

PARK GRILL / BBQ GRILL

This model marks the 500th to the RevitCity community !!!

100's of more free downloads @ PARAMETRICCOMPONENTS.COM

Product Version: Revit Architecture 2017

4382 Downloads

Simple 6/12 slope scissor truss.  This family comes fully parametric with respect to bearing width, overhang depth and member sizes.  

If you need a different slope this is a good family to start from and modify to fit your project.

Hope you find it helpful!

Product Version: Revit Architecture 2018

1793 Downloads

Simple FLOOR BASED canister style up-light which is perfect for exterior situations.

Fully parametric: Materials and size. Made with Revit v2015 

Enjoy! Free for personal, non comercial use ;)

I am pretty sure you will like it so Rate, Comment, or sugest how to improve and check my other uploads!

Product Version: Revit Architecture 2015

32775 Downloads

Here is a bottle of Tide laundry soap to add that extra detail to your renderings. Materials are listed under Tide Bottle for an easy change to any material or color that you would like. Not Parametric, just the size of an average laundry soap bottle. Bottle is a little over 9" tall. Let me know what you all think and if its helping?

Product Version: Revit Architecture 2017

3777 Downloads

Four panels patio door, parametric material, overall width, and length and door width.

Built using Revit architecture 2012 

nirim  

Product Version: Unknown

2736 Downloads

Adjustable shape trapozoidal or unithick Isolated footing for str. columns. with Base & 2 Varable Pedestals  fully parametric Ver 2015 by Er. L.J.Upadhyay.

Product Version: Revit Architecture 2015

1807 Downloads

Almost fully parametric. Height, width, frame size, handle height. Frame, door panels - materials.

Please leave comments and suggestions.

No Rating

Product Version: Revit Architecture 2012

6352 Downloads

Revit railing possibilities are not yet so flexible as they should be, so instead of making railing with glass panels, I made railing as curtain wall panel. to use this file within a curtain wall as curtain panel select this .rfa file.  With fixed distance (vertical grid parameter) you can set lenght of panels with balusters.

Absolutely parametric model, all dimensions(balusters,holders,fixings,handrail) and material.

Product Version: Revit Architecture 2012

16970 Downloads