Key Card (w/ electrical conduit connector)

Product Version: Revit Architecture 2017

1357 Downloads

MIFAB® Series F1100-C-90 lacquered cast iron floor drain with threaded side outlet, anchor flange, cast iron membrane clamp ring with primary and secondary weepholes for waterproofing membrane, and standard reinforced (specify diameter), (specify strainer finish)

strainer. (For non-membrane floors, use MIFAB F1100-90 Series.)

No Rating

Product Version: Unknown

32 Downloads

Parametric Elevator Sump Pump. Adjustable San and Electrical paramenters. Could add a parameter for oil minder for hydraulic elevators.

No Rating

Product Version: Revit MEP 2015

4093 Downloads

http://plastec.com.au/wp-content/uploads/2018/09/18997-18977-Fact-Sheet.pdf

No Rating

Product Version: Revit MEP 2018

893 Downloads

A basic ceiling mounted strip light.  Material and length can be adjusted.  Includes light source and electrical connection.

No Rating

Product Version: Unknown

1418 Downloads

IT APPLICABLE FOR A RANGE UPTO 12MM TO 1000MM ABOVE.

FULLY PARAMETRIC WITH ONE OPERATING PARAMETER.

MATERIALS APPLIED.

ELECTRICAL CONNECTIONS GIVEN 

NOTE:ITS NOT AS PER STANDARD JUST AN GENERIC MODEL

MODEL INFO NOT ADDED.

Product Version: Revit MEP 2014

1340 Downloads

Horizontal Bottle Cooler, based on the True Manufacturing TD-50-18, and very similar to the Ascend Refrigeration JBC-50.  No electrical hookup, but created from the True 3d ACAD model, so it is almost exact.

No Rating

Product Version: Revit Architecture 2011

2076 Downloads

Parametric Sewage/Garage Ejector with San, Vent connections and Electrical parameters. Adjustable pit dimension and depth. Probably should have separate width and length parameters.

No Rating

Product Version: Revit MEP 2015

888 Downloads

For leading cables through the roof membrane on flat roofs in a watertight manner. E.g. at solar panels, air conditioners and other electrical equipment.

No Rating

Product Version: Revit Architecture 2019

53 Downloads

Electrical transformer made in Revit drawn by Jeff Rath

www.3d3ntourage.com

Product Version: Revit Architecture 2008

3793 Downloads

Telephone Point - Vertical (w/ electrical conduit connector)

No Rating

Product Version: Revit Architecture 2017

1638 Downloads

Telephone Point - Horizontal (w/ electrical conduit connector)

No Rating

Product Version: Revit Architecture 2017

1440 Downloads

True Revit 3D Face Based 4gang Architrave Light Switch complete with render materials for all faces plus electrical connectors and 2D plan switch symbol.

drawn by www.electricalrevitfamilies.com

No Rating

Product Version: Revit MEP 2009

2325 Downloads

Fully parametric Louver Panel Folding Door

For LV Room or Electrical Sub-station

Product Version: Revit Architecture 2014

32781 Downloads

24" swing back bar.  Modeled after the True Manufacturing TBB-24-48.  Floor based model, no electrical connection.

No Rating

Product Version: Revit Architecture 2011

2410 Downloads

Doorbell & DND (Do-Not-Disturb) Indicator w/ electrical conduit connector

No Rating

Product Version: Revit Architecture 2017

1252 Downloads

A black metallic floor lamp with electrical connection.  Enough Said....

Product Version: Revit Architecture 2012

6491 Downloads

For leading cables through the roof membrane on flat roofs in a watertight manner. E.g. at solar panels, air conditioners and other electrical equipment.

No Rating

Product Version: Revit Architecture 2019

45 Downloads

90" Back bar.  Based off of True Manufacturing TBB-4.  Modeled from the True 3D Acad files, so it is very close.  Floor based model, no electrical connection.

No Rating

Product Version: Revit Architecture 2011

5582 Downloads

2-Gang Single Pole Switch (w/ electrical conduit connector)

Product Version: Revit Architecture 2017

8524 Downloads

1-Gang Single Pole Switch (w/ electrical conduit connector)

Product Version: Revit Architecture 2017

8585 Downloads

A commercial freestanding dishwasher made to Eurodib's specs.  All piping and electrical information provided in type properties.  All componets have parameters set for materials.  I spent a lot of time on this one just for my revitcity friends.  Please rate and comment

Product Version: Revit MEP 2010

9635 Downloads

A parametric water boiler from Heliotek (Bosch), models MK(P) 200, 300, 400, 500 and 600(Lts). For use with solar thermal collectors. Also has a electricl conector for a 2500W internal electrical resistance heating.

Modeled by dufbp, made by Bosch.

Country: Brazil

Product Version: Revit Architecture 2017

5583 Downloads

The parametric door contains embedded threshold along with standard ironmongery required in a ELV Room, Telecom Room and Electrical Room door.

No Rating

Product Version: Revit Architecture 2014

4770 Downloads

An underbar beer dispenser absed on the True Manufacturing Model TDD-3.  This was built from the 3D model provided from True.  As far as I am concerned, it is an exact match.  The family is floor based but does not include any electrical hookups, however that would be easy to add.

No Rating

Product Version: Revit Architecture 2011

3526 Downloads

The Pronto!™ FD-190-PR-60 PVC adjustable floor drain offers 1 3/4” pre- and 7/8” post-pour adjustability with an integrated bubble level, two leveling shims and a reversible clamping collar with weepholes to ensure professional results. This floor drain also features an anchor flange, round nickel bronze strainer, and a solvent weld outlet. Options include vandal-proofing, trap primer tapping, a backwater valve, side outlet and a choice of funnels.

No Rating

Product Version: Revit Structure 2014

722 Downloads

MIFAB® Series R1940 downspout nozzle with nickel bronze body and threaded outlet, wall anchor flange with countersunk holes and decorative outlet nozzle.

No Rating

Product Version: Unknown

141 Downloads

For leading cables through flat roof surfaces with bitumen or foil (single ply) roof membranes in a watertight manner. E.g. at solar panels, air conditioners and other electrical equipment. The detachable bends makes installation flexible and easy to handle.

No Rating

Product Version: Revit Architecture 2019

113 Downloads

A switch with an invisible model line at 7', so if you set your RCP cut plane to just below 7', outlet symbols will show up.  This one is a 3-way switch

Product Version: Revit Architecture 2008

8854 Downloads

For leading cables through flat roof surfaces with bitumen or foil (single ply) roof membranes in a watertight manner. E.g. at solar panels, air conditioners and other electrical equipment. The detachable bends makes installation flexible and easy to handle.

No Rating

Product Version: Revit Architecture 2019

45 Downloads