Series 709DCDA Double Check Detector Assemblies prevent backflow of non-health hazard fire protection system substances from being pumped or siphoned into the potable water supply. They incorporate a meter to detect ground leaks and unauthorized illegal taps, greatly reducing annual water expenses. Their compact epoxy coated cast iron unibody and modular check design facilitate simple and easy installation and maintenance. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

302 Downloads

Bulky Sofa with cusions

Product Version: Revit Architecture 2014

31679 Downloads

Series 757, 757N Double Check Valve Assemblies prevent the backflow of pollutants that are objectionable but not toxic, from entering into the potable water supply. Its compact housing consists of two independently operating tri-link check valves, two shutoff valves, and four test cocks. It features a stainless steel housing and sleeve and is 70% lighter than traditional designs. Series 757, 757N is designed for non-health hazard applications and may be installed under continuous pressure service to protect against both backpressure and backsiphonage. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

387 Downloads

Fully Adjustable  Door material can be changed in materials.

No Rating

Product Version: Revit Building 9

2766 Downloads

Just a simple stove,

No Rating

Product Version: Unknown

3889 Downloads

glass - no trim

Product Version: Unknown

23407 Downloads

glass - no trim

No Rating

Product Version: Unknown

9584 Downloads

My second upload. Almost fully parametric. I didn't make any family types for it. It's pretty big (small store front wall)

Product Version: Revit Architecture 2008

13547 Downloads

Series 757 Double Check Valve Assemblies prevent the reverse flow of liquids in a plumbing system due to backpressure or backsiphonage where there is a non-health hazard. Compact design and lightweight stainless steel construction (70% lighter than traditional designs) makes installation easier and faster. For unmatched versatility, assemblies are available for horizontal, vertical, or N pattern installations while groove connections allow ease of installation and pipe alignment. Patented tri-link check assemblies are also designed for easy serviceability. A variety of shutoff valve options are offered.

No Rating

Product Version: Revit MEP 2014

835 Downloads

Majesta Double Hungs are Kolbe's newest product.All units are custom made-to-order, therefore there are no standard sizes.• Maximum frame size: 6’ x 12’• Minimum frame size: 3’-6” x 6’-5”• Minimum basic jamb size: 6-9/16”• Other size limitations may apply, depending on the options chosen• Sash: nominal 2-1/4” thick• Spiral balance system• Concealed jambliners• Standard locking hardware: innovative pin style lock at the top of the top sash and bottom of the bottom sash; no checkrail locks as standard• Sash are removable, but do not tilt-in• Triple insulating glass available!

No Rating

Product Version: Revit Architecture 2010

958 Downloads

Aluminum and tempered glass window showing handles. All dimensions and materials parametrized. Metric.

Product Version: Revit Architecture 2008

44075 Downloads

This American Woodmark model is their double oven, 84" high, 2 butt doors, 1 drawer cabinet.   American Woodmark offers this cabinet in two widths: 27" and 30" and those are the two family types.   All doors and the drawer operate independently.   The oven width for each cabinet size is preset to the published size, but I've exposed the oven opening parameters as instance parameters if you want to cut a custom opening.

The best practice for operating the doors is to open and close them in angular increments of something less than 90° in a single operation. For example, if you want to open them to 90°, you could open them initially to 50° and then go to 90°. Close them the same way.

No Rating

Product Version: Revit Architecture 2013

4392 Downloads

two medium sized lockers stacked vertically

No Rating

Product Version: Revit Building 5.1

10095 Downloads

This is a gate that has corrugated metal sheathing and is meant to be placed in a wall.  Width and height are adjustable in the Type Parameters.  (6', 8', 10', and 12' widths)

Product Version: Revit Architecture 2009

19552 Downloads

Fully adjustable

No Rating

Product Version: Revit Building 9

2744 Downloads

This American Woodmark model is their double oven, 90" high, 2 butt doors, 1 shelf, 1 drawer cabinet.  American Woodmark offers this cabinet in three widths: 27", 30", and 33" and those are the three family types.  All doors and the drawer operate independently.  The oven width for each cabinet size is preset to the published size, but I've exposed the oven opening parameters as instance parameters if you want to cut a custom opening.

The best practice for operating the doors is to open and close them in angular increments of something less than 90° in a single operation. For example, if you want to open them to 90°, you could open them initially to 50° and then go to 90°.  Close them the same way.

No Rating

Product Version: Revit Architecture 2013

3106 Downloads

Series 719 Double Check Valve Assemblies are designed to protect drinking water supplies from dangerous cross-connections in accordance with national plumbing codes and water authority requirements. They have a bronze alloy body construction and chloramine resistant elastomers. Series 719 features a separate access, top-entry check valve design for ease of maintenance and is for use at referenced cross-connections in non-health hazard applications. Check with local inspection authorities for installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

312 Downloads

This American Woodmark model is their double oven, 96" high, 2 butt doors, 2 shelves, 1 drawer cabinet. American Woodmark offers this cabinet in three widths: 27", 30", and 33" and those are the three family types. All doors and the drawer operate independently. The oven width for each cabinet size is preset to the published size, but I've exposed the oven opening parameters as instance parameters if you want to cut a custom opening.

The best practice for operating the doors is to open and close them in angular increments of something less than 90° in a single operation. For example, if you want to open them to 90°, you could open them initially to 50° and then go to 90°. Close them the same way.

No Rating

Product Version: Revit Architecture 2013

3250 Downloads

Turn on and off casing type or handle, or edit more as you wish...ENJOY!

Product Version: Revit Architecture 2012

5955 Downloads

Two story chimney that automatically creates into the wall. The Materials are changable from the elements properties. Let me know what you think. rate please

Product Version: Revit Architecture 2010

3034 Downloads

Iron dbl gate between two decorative columns.
Parametric.

Product Version: Unknown

58917 Downloads

No Rating

Product Version: Revit Architecture 2019

1950 Downloads

Product Version: Revit Architecture 2019

1758 Downloads

The hollow metal frame will wrap around the wall and will automatically adjust to the wall width.

Product Version: Revit Architecture 2011

6177 Downloads

 THIS IS A DOOR W/ SOLDIER COURSE AROUND 3SIDES AND A KEYSTONE @ TOP CENTER

Product Version: Unknown

8492 Downloads

Here is a two door cabinet wall mounted with lower drawers(Thomasville line) modeled by Team RPM

No Rating

Product Version: Unknown

9716 Downloads

two large lockers arranged horizontally

Product Version: Revit Building 5.1

9469 Downloads

Door & Frame Materials, Undercut, Jamb Thickness (for Rough Opening), Open angle (instance)

Product Version: Revit Architecture 2008

6012 Downloads

Series LF709 Lead Free* Double Check Valve Assemblies prevent the reverse flow of polluted water from entering into the potable water supply. They have a modular check design for easy maintenance and epoxy coated (FDA approved) cast iron body construction. Series LF709 is ideal at referenced cross-connections identified in non-health hazard applications. The LF709 features Lead Free* construction to comply with Lead Free* installation requirements. Maximum Working Pressure: 175psi (12.06 bar).

No Rating

Product Version: Revit MEP 2014

354 Downloads

Wooden Window

Changeable Sizes

Changeable Material

No Rating

Product Version: Revit Architecture 2013

1151 Downloads