SPECIFICATIONS

• operatingfrequency range
  
  33 Hz - 200 Hz -3dB27 Hz - 260 Hz -10 dB
  
  


• continuous output
  
  126 dB SPL
  
  


• peak output
  
  132 dB SPL
  
  


• sensitivity
  
  100 dB SPL (2.83 Volts into rated Z, at 1 meter), measured in half space
  
  


• driver complement
  
  one 12" Long Excursion Woofer
  
  


• dimensions
  
  38 x 18 x 30.2 inches
  
  


• weight
  
  142 lbs
  
  


• Rated Impedance
  
  8 Ohms
  
  


• Power Rating
  
  400 W continuous, 800 W program
  
  


• 
  
  http://www.danleysoundlabs.com/products/subwoofers/tapped-horns/th112/
  
  

No Rating

Product Version: Unknown

98 Downloads

SPECIFICATIONS

• operatingfrequency range
  
  48 Hz - 200 Hz - 3 dB 41 Hz -10dB
  
  


• continuous output
  
  129 dB SPL
  
  


• peak output
  
  135 dB SPL
  
  


• sensitivity
  
  101 dB SPL (2.83 Volts into rated Z, at 1 meter) measured in half space
  
  


• driver complement
  
  one 12" long excursion woofer
  
  


• dimensions
  
  24 x 15 x 24 inches
  
  


• weight
  
  76 lbs
  
  


• Rated Impedance
  
  8 Ohms
  
  


• Power Rating
  
  700 W continuous, 1400 W program
  
  


• 
  
  http://www.danleysoundlabs.com/products/subwoofers/tapped-horns/thmini/
  
  

No Rating

Product Version: Unknown

98 Downloads

SPECIFICATIONS

• coverage Pattern
  
  140 x 10
  
  


• operatingfrequency range
  
  77 Hz – 15 kHz +/- 3 dB50Hz – 18 kHz -10 dB
  
  


• continuous output
  
  127 dBSPL
  
  


• peak output
  
  133 dBSPL
  
  


• sensitivity
  
  99 dBSPL measured at 10M @ 28.3V input
  
  


• driver complement
  
  Eight - 5” Coaxial drivers
  
  


• dimensions
  
  60”H x 9”W x 9”D
  
  


• weight
  
  100 lbs.
  
  


• Rated Impedance
  
  4 ohms
  
  


• Power Rating
  
  1300 watts continuous 5200 watts peak
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/sbh/sbh-10/
  
  

No Rating

Product Version: Unknown

860 Downloads

SPECIFICATIONS

• operatingfrequency range
  
  33 Hz - 200 Hz - 3 dB27 Hz – 200 Hz -10dB
  
  


• continuous output
  
  140 dB SPL
  
  


• peak output
  
  146 dB SPL
  
  


• sensitivity
  
  110 dB (2.83 Volts into rated Z, at 1 meter), measured in half space
  
  


• driver complement
  
  four 12" long excursion woofers
  
  


• dimensions
  
  26.5 x 45 x 45 inches
  
  


• weight
  
  357 lbs
  
  


• Rated Impedance
  
  Switchablea single 2 ohm loadortwo 4 ohm loads
  
  


• Power Rating
  
  4000 W continuous 8000 W program
  
  


• 
  
  http://www.danleysoundlabs.com/products/subwoofers/tapped-horns/th412/
  
  

No Rating

Product Version: Unknown

110 Downloads

Just in Case somebody want to work on the single block and work on different layers of vent block instead of the 10 layers in the parametric

Product Version: Unknown

1499 Downloads

SPECIFICATIONS

• coverage Pattern
  
  60 by 40
  
  


• operatingfrequency range
  
  43 Hz - 20 kHz
  
  


• continuous output
  
  Band dependent, 150 dB SPL
  
  


• peak output
  
  Band dependent >150 dB SPL
  
  


• sensitivity
  
  112 dB SPL average, (2.38 volts into rated Z at 1 meter)
  
  


• driver complement
  
  Six 15" wooferseight 6.5"midsHigh/Mid & High, four Coaxial compression drivers
  
  


• dimensions
  
  30 X 35.6 X 48 inches
  
  


• weight
  
  432 Lbs
  
  


• Rated Impedance
  
  Low Freq, Two 3 ohm loadsMId range a single 4 ohm loadHigh, a single 4 ohm load
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/jericho/j3/
  
  

No Rating

Product Version: Unknown

624 Downloads

SPECIFICATIONS

• coverage Pattern
  
  90˚ horizontal x 40˚ vertical (0˚ on axis, 40˚ down -6dB)
  
  


• operatingfrequency range
  
  47 Hz - 18 kHz +/-3dB37 Hz - 24 kHz -10dB
  
  


• continuous output
  
  148 dB SPL
  
  


• peak output
  
  151 dB SPL
  
  


• sensitivity
  
  Band dependent
  
  


• driver complement
  
  six 18" woofers six 6" midrange drivers three coaxial HF drivers
  
  


• dimensions
  
  60 x 45 x 30 inches
  
  


• weight
  
  720 lbs
  
  


• Rated Impedance
  
  Low frequency, 6 x 4 ohm loads Midrange, 1 single 6.5 ohm load Mid High, 1 single 2.7 ohm loadHigh, 1 single 3 ohm load
  
  


• Power Rating
  
  LF > 12,000 W total, MR > 1200 W, MId hi >600 W, HF > 400W
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/jericho/jh-90/
  
  

No Rating

Product Version: Unknown

529 Downloads

THIS TREE IS THE SAME AS MY" JONATHAN FURLONG'S ADVANCED 3D/2D TRESS" BUT HAS NO WHITE SIDE.THIS TREE WILL DISPLAY IN BOTH 2D AND 3D. IN 2D IT IS COLOURED HATCHING. IN 3D IT IS COLOURED AND HATHED. IT RENDERS LIKE THE NORMAL TREES FROM THE STANDARD METRIC LIBARY.

Product Version: Unknown

21754 Downloads

Samsung 28" Screen, Keyboard and Mouse.

Screen has generic REVIT screen display - just done as object lines etc so you do not have to have full on rendering to see.

You can easily remove any of the three items - Monitor, Keyboard or Mouse - all three done as seperate  families.

Desk and chair not included.

Feel free to comment

Product Version: Revit Architecture 2014

26242 Downloads

Modeled the University of Utah Football Field for a class project. Though I would share it in case anyone ever needs it. Not parametric, it is the exact size of the field currently sitting in the stadium. Materials are also listed under the properties tab in the edit type section for an easy change to any material or color that you would like. Enjoy!

Product Version: Unknown

3022 Downloads

Coalesse - Topo

Topo desking features space division and display walls, desktops and desk loops, Sliding window screens, roller screens, modesty screens and overhead towers. Flexibility to fit how and where you work - for the open plan and private office.

COALESSE

No Rating

Product Version: Unknown

3806 Downloads

Coalesse - Topo

Topo desking features space division and display walls, desktops and desk loops, Sliding window screens, roller screens, modesty screens and overhead towers. Flexibility to fit how and where you work - for the open plan and private office.

COALESSE

No Rating

Product Version: Unknown

3997 Downloads

Coalesse - Topo

Topo desking features space division and display walls, desktops and desk loops, Sliding window screens, roller screens, modesty screens and overhead towers. Flexibility to fit how and where you work - for the open plan and private office.

COALESSE

Product Version: Unknown

5456 Downloads

Coalesse - Topo

Topo desking features space division and display walls, desktops and desk loops, Sliding window screens, roller screens, modesty screens and overhead towers. Flexibility to fit how and where you work - for the open plan and private office.

COALESSE

Product Version: Unknown

6996 Downloads

A quick model of the Butterfly MX 11.6" screen recessed entry panel for entry access for apartment buildings.  

This family is wall hosted, but you can also open the hosted panel family to insert into a different family type if desired.

Materials are parameter controlled, dimensions are not.  I included a parameter for wall assembly depth in case you need to offset the box for any specific additional depth at unique conditions.

Enjoy!

No Rating

Product Version: Revit Architecture 2020

728 Downloads

SPECIFICATIONS

• coverage Pattern
  
  90 by 60
  
  


• operatingfrequency range
  
  37 Hz - 10 kHz -3 dB27 Hz - 15 kHz -10 dB
  
  


• continuous output
  
  Band dependent, average 138 dB SPL
  
  


• peak output
  
  Band Dependent, average 145 dB SPL
  
  


• sensitivity
  
  Band Dependent , average 113 dB SPL
  
  


• driver complement
  
  Low Freq six 18" woofersMid Range twenty four 5" mids, High Freq Twelve 1" compression drivers
  
  


• weight
  
  600 Lbs
  
  


• Rated Impedance
  
  band dependent LF 3 ohms Mids 4 ohmsHigh Freq. 4 ohms
  
  


• 
  
  http://www.danleysoundlabs.com/products/loud-speakers/jericho/jh-2/
  
  

No Rating

Product Version: Unknown

322 Downloads

Wall based   (H-ONT)    Home - Optical Network Terminal by Chorus NZ for fibre to the home installation (FTTH)

4 data port, 2 telephone ports, 230 v power and earth/comms.

Materials for various LED lights, case and ports.

MEP connections:  power, data and telephone

CBI (NZ)  78-11  cable communication systems

Revit 2018

Product Version: Unknown

1245 Downloads

New english version with report function.

This door is not a so simple one.

Free variable parameters:

Door width, Door height,

Sill on/off switch- blinds on/off switch,

blinds put up/down function with shading procent parameter,

built-in blinds on/off switch,

you can set the door opening angle (look the doorhandle),

you can modify the section number (case number),

you can set the opening section position,

the section number is able to set unlimitedly.

On the picture only one door element is seenable!

It was made by an building ingenieur not by an architect. My colleague told me to write this...

Product Version: Revit MEP 2010

7205 Downloads

Laundry Cart on casters. Optional hanging rack visibility parameter. Commonly used in commercial laundromats.

Product Version: Revit Architecture 2019

2503 Downloads

Parametric round table - Dimensions: 140 cm diam. h. 76 cm - Central column in turned wood

Product Version: Revit Architecture 2015

20637 Downloads

I have taken a manufacturers family - redrew it - so every curve is tangentle to other planes - hence with lines on - no lines between formed surfaces. This is how drawing should be. When 3D view set at Scale 1:1 - therefore no thick line work. In this instance no linework turned on anyways.

Manufactured items in sheetmetal, plastics, timber etc, it is vare rare to have a sharp corner on it. All planes should have a radiused chamfer - just look around your office - hard to find two surfaces coming together with sharp edge. 

Have posted this here solely to assist others on how to draw and also how to display.

To many rubbish families posted here - learn and create each one better than the last one.

Any comments - feel free - 

Product Version: Revit Architecture 2014

9636 Downloads

This is light 3D object, meaning thet the geometry is simplified to maximum for better performance, yet with good enough graphical representation in all views. Cabinet under counter can be turned off so you can use one family for both - cabinets and/or countertops. Separate family just for countertop alone is only 36 kB smaller in size, so I thought it is more efficient to use just this one famlily for two cases. Dims are instance parameters which allows size adjustments by easy dragging and then precize it with manual input of values.  This way speeds up work when designing spaces with many objets of this kind, like restaurant kitchens, etc. 

The only thing is that dragging one of the ends along the long side may generate errors, in this case simply drag the other end. Or if you are able to fix this issue you are welcome to upload a corrected version. 

Product Version: Revit Architecture 2018

1603 Downloads

Product Version: Revit Architecture 2010

21471 Downloads

This is a muly cell auto dimension Box Bridge for road.

In autoset dimension for foundation Raft, end & inner webs as well as deck slab is set as per span, while in MORTH setting one can set these dimensions manually.  For longer length of bridge  repet & align family providing expansion joints. In this case Return walls & approach slabs be off. Provision to off/on for Cut off wall, Raft Key, left & right Return wall & Approach Slab have been provided. Railing of main bridge / on approach can be set indepentely. Number of span is ristricted as total length of bridge may not exceed 30 mtrs. for more length add more bridge. The box type bridge is revised up to date, as this was loaded in 2006 on this site. Lallan Ji Upadhyay. Varanasi.

No Rating

Product Version: Revit Architecture 2015

973 Downloads

Stainless steel simple railing with glass panels and pliers - Parametric - Export 3d Studio OK

Product Version: Revit Architecture 2015

14658 Downloads

Rinnai VT26 gas califont,  wall based.

MEP connections for gas supply, cold water IN, hot water OUT, 230 v electrical power supply,  no condensate drain  (optional on this model),  materials for  white spray painted metal case, manufacturer logo, copper tubing.

CBI (NZ)  Liquid  71-26 hot potable water reticulation systems

Has local NZ gas regulations module placement on wall relative to window or doors, dowpipes, balconies, internal corners and ground lines as diagram with Yes/No parameter control -  place the unit on the wall and the unit and diagram appear, move to suit the annotated lines until module in correct  place,  click then select Properties and turn off the 2D diagram,  leaving the module alone on the wall.

Modeled from local NZ Rinnai web site  literature.

Revit 2018

Product Version: Unknown

588 Downloads

In autoset dimension for foundation Raft, end & inner webs as well as deck slab is set as per span, while in MORTH setting one can set these dimensions manually.  For longer length of bridge  repet & align family providing expansion joints. In this case Return walls & approach slabs be off. Provision to off/on for Cut off wall, Raft Key, left & right Return wall & Approach Slab have been provided. Railing of main bridge / on approach can be set indepentely. Number of span is ristricted as total length of bridge may not exceed 30 mtrs. for more length add more bridge. The box type bridge is revised up to date, as this was loaded in 2006 on this site. 919919640999 Lallan Ji Upadhyay. Varanasi. Any Query will be welcomed.

No Rating

Product Version: Revit Structure 2019

562 Downloads

Currently building an exact scale revit model of Nuketown the Call of Duty course. Thought that I would upload the sign that I built just in case any of you want it or need it. Not Parametric,it is a little over 6'3" tall and 9' wide. Let me know what you all think?

Product Version: Revit Architecture 2018

795 Downloads

It is a RCC Box Bridge for one to multy spans. Number of spans, Clear span, Clear height , Road width params can be set independentely. Approach slab, Return walls, Cutoff walls, Drop key etc. can be placed/remove at will. In autoset dimension for foundation Raft, end & inner webs as well as deck slab is set as per span, while in MORTH setting one can set these dimensions manually.  For longer length of bridge  repet & align family providing expansion joints. In this case Return walls & approach slabs be off. Provision to off/on for Cut off wall, Raft Key, left & right Return wall & Approach Slab have been provided. Railing of main bridge / on approach can be set indepentely. Number of span is ristricted as total length of bridge may not exceed 30 mtrs. for more length add more bridge. The box type bridge is revised up to date, as this was loaded in 2006 on this site. Lallan Ji Upadhyay. Varanasi.

No Rating

Product Version: Revit Structure 2018

495 Downloads

This couch looks like the EDRA Damier sofa.

It's fully parametric with three levels of detail (flat couch in coarse and medium levels).

 

Product Version: Revit Architecture 2012

9848 Downloads