This door has elevation and plan swing lines for both ways.  The swing lines are set to only be visible in coarse and medium settings.  Material parameters set for the panel, both kick plates, and the door frame.  Made form Eliasons specs and documents.  Please rate and comment.

Product Version: Revit Architecture 2010

3969 Downloads

Fully Parametric Garage Door

Product Version: Unknown

39793 Downloads

This is a generic door family provided by www.Revitopia.com. It utilizes embedded families to allow concentrated design on the pieces that make up a door with minimal breaking. Its a result of door development for the designer/architects use.

Product Version: Unknown

1179 Downloads

Series ISCA-101-L/R Industry Standard single horizontal adjustable water closet carrier with epoxy coated cast iron fitting, 4 in. (102mm) no hub waste and 2 in. (51mm) no hub vent connections, epoxy coated cast iron patent pending compression seal faceplate assembly, epoxy coated cast iron foot supports adjustable for standard and wheelchair height, adjustable ABS nipple with integral test cap and neoprene bowl gasket, plated hardware and chrome cap nuts. The closet carrier legs are embossed with incremental measurements markings, allowing contractors to easily adjust the height of the carrier to the most commonly used fixture requirements.

No Rating

Product Version: Unknown

128 Downloads

Rectangular resizeable cabinet with awining glass door. Door can be opened, closed or parcially opened. You can change cabinet and glass thickness.

No Rating

Product Version: Unknown

4401 Downloads

Parametric material and length.  Commericial metal door pull with eased edge perpindicular handle profile

REVIT 2017

No Rating

Product Version: Unknown

5380 Downloads

Its a fully parametric wooden door with 6 panels , Frame , 3 hinges and handle at both interior and exterior .

It has Instant opening parameter , so it can be opened upto any angle .

Product Version: Revit Architecture 2019

1145 Downloads

Gate Garage Door. Fully parametric. Door and side panels are controlled separately. (Side panels can be turned off individually if they are not needed. There are a lot of math calculation in this family so when changing sizes it is a little slow. 

Rvt 15

Hope it helps,

smh

Product Version: Revit Architecture 2015

11128 Downloads

Improved parametric hollow metal doors from my post dated August 31, 2011.You can open the "Door Schedule View", switching "Door Type" from #1 thru #4, and watching the door panel changes on 3 D view.You can also check/unckeck "Exterior Door", to swith the "(5) GLASS" from "SG" - safety glass, to "SGI" - safety glass-insulated.If you like it, you can download the door families in  the drawing mentioned above as bases, adding parameters shown here, and creat your own set of parametric door families. Enjoy!

Product Version: Revit Architecture 2009

11335 Downloads

A fully parametric door with many family types already made.  Has two windows & two panels.  Also has a frame that goes around the inside of the opening.

Product Version: Revit Architecture 2011

16652 Downloads

Stile and rail door with parametric dimensions and materials.

No Rating

Product Version: Revit Architecture 2016

1225 Downloads

Here is a door that you can set the angle that you want so it will be open in a walkthrough

Product Version: Unknown

2746 Downloads

Generic floor mounted door stop

No Rating

Product Version: Unknown

2719 Downloads

Single flush type door

No Rating

Product Version: Unknown

679 Downloads

This double door is fully parametric.

Product Version: Revit Architecture 2014

32345 Downloads

Overhead Door adjustable for width.

No Rating

Product Version: Unknown

13077 Downloads

Front door made at NOHS.

Product Version: Unknown

13472 Downloads

Sliding door to fit in Curtain Wall.  Based on Curtain Wall Panel Door by dylan88.

Product Version: Revit Architecture 2008

24245 Downloads

Carriage house door based on a photograph of a RealCraft carriage house garage door. Width and height are parametric.

No Rating

Product Version: Revit Architecture 2020

1299 Downloads

This door family is parametric it has, 2D and 3D swings. it also has frames that is parametric. This file is made in revit 2016 you won't be able to open it in older version. 

No Rating

Product Version: Unknown

657 Downloads

End hinging panel fold door full adjustable including number of panels and folding angle.

Product Version: Unknown

57810 Downloads

Sliding industrial door with functioning window openings. Appears correctly in plans, elevations, and model. Can specify materials.

Product Version: Revit Architecture 2008

11056 Downloads

Decour single mahogany entrance door with oval glass and moulded wooden panels 

Product Version: Revit Building 9

7621 Downloads

NOHS victorian front door full house stain glass decorative ornate 

No Rating

Product Version: Unknown

8507 Downloads

Simple but efective 4 panel sliding door, made of aluminium and 6mm glass, fully parametric.

Product Version: Unknown

129248 Downloads

Parametric exterior pivot door

Visit https://www.r7designs.com/ for more famalies

Revit 2023

Product Version: Unknown

7798 Downloads

This is a single residential garage door created with the standard track found in the Clopay revit models.  It is fully-parametric up to 9'-8" wide (based on track restrictions) and with trim that can be turned off.

Product Version: Revit Architecture 2014

12944 Downloads

Multi-panel garage door for widths of 9 feet or more. Number of panels is fixed; the frame is metal.

Product Version: Revit Building 9

48211 Downloads

this family is for projects where there are existing vault doors. You can change the height and width of the door

Product Version: Unknown

2556 Downloads

This is a 6 panel exterior outswing door w/ transom and 45 degree plan symbol.

Product Version: Revit Architecture 2008

14910 Downloads