Hey guys, I noticed that someone posted a Parametric Slab Family in here, but nobody could've download it. Apparently it was a fake.

A while ago I managed to get a real Parametric Slab Family (with joists and bricks), but I don't remember from where or who is the author, but I decided to post it here, so other people could use it too.

PS: I DIDN'T DEVELOPED THIS FAMILY, SO, IF THE AUTHOR SHOWS UP AND ASK ME TO REMOVE IT, I WILL REMOVE IT.

How to use: Load the family "Laje_de_Forro_Parametric_Slab_17204.rfa" in the project and create a Beam System. Change the Beam Type to "Vigota Treliçada..." and you will see the joists. Use Fixed Distance of 0,43 m. Then select one or all the joists (not the beam system) and you will see the option "Visibilidade da Lajota" in the bottom of the Properties Panel. Check it to enable the brick. That is it.

---------------------------------------------------- 

Olá pessoal, eu percebi que alguém postou uma Família Paramétrica de Laje de Forro aqui, mas ninguém conseguia baixar ela. Aparentemente era uma montagem.

A alguem tempo atrás eu consegui uma Família de Laje de Forro real (com vigotas e lajotas), mas não consigo me lembrar onde e quem era o autor, mas decidi postar aqui, para que outras pessoas pudessem usá-la também.

OBS: EU NÃO DESENVOLVI ESSA FAMÍLIA, ENTÃO, SE O AUTOR APARECER E PEDIR PRA REMOVER, EU VOU REMOVER.

Como usar: Carregue a família "Laje_de_Forro_Parametric_Slab_17204.rfa" no projeto e crie um Sistema de Vigas. Mude o Tipo de Viga (Beam Type) para "Vigota Treliçada..." e você verá as vigotas. Use Distância Fixada de 0,43m. Depois selecione um ou todas as vigotas (não o sistema de vigas) que você verá a opção "Visibilidade da Lajota" no fundo do Painel de Propriedades. Marque essa opção para habilitar as vigotas. Pronto, é isso.

Product Version: Unknown

3808 Downloads

Stainless Steel Window Washers Tie Down Bolt. Generic Model with 2 Parametric lengths for Height above the level (Typically Roof) and below down to the steel beam level

Product Version: Revit Architecture 2008

1899 Downloads

Generic swing stage scaffold - overhang, beam length, platform parameters and platform drop are adjustable.  Revit version 2016.

Product Version: Revit Architecture 2015

4984 Downloads

Craftsman Style exterior built up quad column with tapered concrete base and wood beam capital top. Has parametric adjustment. Our own design.

Product Version: Unknown

16364 Downloads

A central vacuum power unit (canister) based on a BEAM vacuum system.  Mounting height is adjustable

Product Version: Revit Architecture 2008

3557 Downloads

Uses STD REvit GLB family modified to slope cut ends of beams to match architectural requirements

Use SlopeHeight and SlopeLength variables to cut the beam. These are schedulable.

Product Version: Revit Structure 2016

155 Downloads

I modified a beam to look like the seam of a metal roof.  Just draw your path, disjoin, and rotate to set upon your metal roof.  The base material is Copper, but you can change that in the properties dialouge. RAC 2009.

Product Version: Revit Architecture 2009

13507 Downloads

Excellent Parametric 2d Framing member for your framing plans. 1 Ply, 2 Ply, 3 Ply or 4 Ply all in one. Could be used as a joist, beam or truss in 2d plan view.

Product Version: Unknown

2325 Downloads

L-angle frame outrigger created as a beam family.  Still trying to figure out how to change the angle sizes; currently it only brings in L2x2x1/4.  Let me know what ya'll think and additional ideas. Thanks

No Rating

Product Version: Revit Structure 2011

1383 Downloads

Single Flute of B-Deck. (Simplified) Created as a structural beam. Ends are adjustable. Allows 3d manipulation. Array to create a panel of B-Deck.  (Join to remove joint line.) Intended more for exposed material as a design element. Don't use for large expanses or it will suck up your memory. 

Product Version: Unknown

10759 Downloads

This is a precast concrete inverted tee beam with individually adjustable seats.

No Rating

Product Version: Unknown

4409 Downloads

8 in 1 Revit family to save you time from downloading each of the equiptment. Pommel Horse and Parallel Bars has landing mat which can be turn off.

Equipment are Ring Tower, Uneven Bars, Single Bar, Vault, Inground Trampoline, Pommel Horse, Parallel Bars and Bnlance Beam.

Enjoy.

Product Version: Revit Architecture 2018

6950 Downloads

Extended End Plate Connection (8 Bolt), full configuable, plate size, plate thickness, bolt location, bolt size, etc. Required to be hosted to an element (ex. beam or column)

Product Version: Revit Structure 2013

7674 Downloads

Extended End Plate Connection (4 Bolt), full configuable, plate size, plate thickness, bolt location, bolt size, etc. Required to be hosted to an element (ex. beam or column). 

Product Version: Revit Structure 2013

8096 Downloads

Fully Parametric Square Water Tank Family.LxBxH & each Cell can adjust. No of Base I Beam & Concrete can change & on/off

Product Version: Revit MEP 2018

975 Downloads

Simple armchair made from an extrusion and lines. Perfect for axonometrics when you don't want to delete a bunch of closely spaced lines in illustrator. The beam is offset to counter line clipping through the table top surface.

No Rating

Product Version: Revit Architecture 2016

1978 Downloads

Single Angle Connection (Single Row), full configuable, angle size, bolt size, number of bolts,  bolt location, etc. Bolts can be toggled on and off (beam and girder size independently) to model a welded/bolted clip angle or all welded clip angle. Required to be hosted to an element (ex. beam or column).

No Rating

Product Version: Revit Structure 2013

3920 Downloads

This is the typical Revit wide flange family that has been modified to introduce a slope cut at the ends of the beams.

Used with architectural features that are structural in nature

Uses Parameters SlopeHeight and SlopeLength to cut the beam. These parameters are shcedulable...

Product Version: Revit Structure 2016

364 Downloads

Simple table made from an flat surfaces and lines. Perfect for axonometrics when you don't want to delete a bunch of closely spaced lines in illustrator. The beam is offset to counter line clipping through the table top surface.

No Rating

Product Version: Revit Architecture 2016

2123 Downloads

Vertical orientated member parametric wood truss. You can adjust length depth, member size, top chord & bottom cord size and top cord extension. works with beam systems.

No Rating

Product Version: Revit Structure 2013

5073 Downloads

Fully parametric Eave Purlin for a Pre-Engineered Metal Building.  Options to change Depth and roof Pitch in Type Properties.  Inspired by "Eave Strut" detail by danpecor and "Zee Purlin" beam by dylan88.

Product Version: Revit Architecture 2011

7030 Downloads

Fully Parametric Square Water Tank Family.LxBxH & each Cell can adjust. No of Base I Beam & Concrete can change & on/off

Product Version: Revit MEP 2018

3532 Downloads

Base Plate Connection - Double Row. Fully configuable, plate size, plate thickness, bolt location, bolt size, bolt spacing, number of bolts, grout pad thickness etc. Required to be hosted to an element (ex. beam or column) or a workplane.

Product Version: Revit Structure 2013

12623 Downloads

Base Plate Connection - Single Row. Fully configuable, plate size, plate thickness, bolt location, bolt size, bolt spacing, number of bolts, grout pad thickness etc. Required to be hosted to an element (ex. beam or column) or a workplane.

No Rating

Product Version: Revit Structure 2013

5155 Downloads

Please rate and comment, thanks!

Took a while to figure out how to get these to work properly.

The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.

The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.com

Cans be individually rotated in project.

!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!

Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).

The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.

You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.

I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.

Hope these are helpfull for you!

Product Version: Revit Architecture 2017

1078 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

Product Version: Revit Architecture 2017

712 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

573 Downloads

Please rate and comment, thanks!Took a while to figure out how to get these to work properly.The track is PureEdge Pipeline with LED uplight (very cool!).  Available in 2', 4', 6', 8', and 10' lengths.  I'll be uploading the 4'-10' pieces.  The hanging height is parametric, but the number of cans and can spacing will have to be changed in family editor.The cans are focus adjustable, dimmable, gallery series artwork LED cans found at cocoweb.comCans be individually rotated in project.!!!DO NOT ROTATE THE CANS BEYOND 179 OR -179 DEGREES OR THEY WILL EFF OFF INTO LOW EARTH ORBIT!!!Can pitch can be individually adjusted but should be kept between 15 and 105 degrees (for some reason the ACTUAL angle is off by 15 degrees, so entering 15 will set the can to zero, or parallel with the track).The can light sources are point+spot.  The beam angle and sourounding field angle can be adjusted as well.You can add cans, but will have to add the corresponding parameters and labels to make the new cans function properly. You'll also have to save the new can as a seperate family, ie. "Can 7", "Can 8", etc.  This was the only was i could figure to get the individual pitch parameters to work.I'm sorry if there's a better/easier way to do all this, but I'm self taught and there's still a lot I don't know.Hope these are helpfull for you!

No Rating

Product Version: Revit Architecture 2017

461 Downloads

Out of the box Revit Wide Flange family with spray on fireproofing added! After a long time of waiting to get to this, I finally did and decided to share because it seems unavailable anywhere else online. It appears to be a highly requested family throughout a lot of forums.

Parameters include, SOFP thickness, Visibility ON/OFF, & SOFP Realistic material. Family can be flexed and does not slow more complex framed structures significantly.

Visible in plan, 3D etc. Sections nicely as well. Great for wall firestopping & MEP coordination.

SOFP will adjust to any size beam selected and will also adjust to medium/fine detail level.

In order for this family to work properly, it’s imperative, the type catalog is located within the same folder as the family. I would suggest keeping them in the default directory together:

C:\ProgramData\Autodesk\RVT 2018\Libraries\US Imperial\Structural Framing\Steel

SOFP material JPG should be loaded into default materials directory as well:

C:\Program Files (x86)\Common Files\Autodesk Shared\Materials\Textures\3\Mats

Hope this is helpful and you enjoy for free! Family was created in RVT2018 but can be upgraded.

No Rating

Product Version: Revit Architecture 2018

853 Downloads

MINISTAGE ROUND SPOT

Art. S.1315W1 MODULES COB 3000K  220-240Vac 1225lm CRI 90 MacAdam step 3Rated luminaire luminous flux: 1040lmRated input power: 11.2WLuminaire efficacy: 93lm/WElectronic ballast  ON/OFF not dimmable CELUMINAIRE TYPEProjector. IP rating IP 66MATERIAL CHARACTERISTICSDie-cast EN AB-47100 aluminium housing with high corrosion resistance.Stone wash surface treatment prior to painting process. A4 grade Stainless Steel screws with 2,5-3% molybdenum content which increases the resistance against corrosion. Silicone gaskets. Painting Process : 3 Step Process1) Surface treatment with BONDERITE. A heavy metal free chemical surface treatment containing ceramic nano particles giving a cohesive, inorganic and highly dense protective coating. 2) PRE POLYMERIZATION a process of introducing an epoxy primer with excellent characteristics to the paint which also offers very high resistance to oxidation due to its Zinc content. 3) POLYMERIZATION a process with the application of polyester powder with high resistance against UV rays and harsh weather conditions. Resistance test protection for Marine applications for 1200h. Mechanical resistance IK 07LIGHTING PERFORMANCE99.98% pure aluminium reflectors, or with concentrating lenses: The sophisticated optics focuses the beam and makes the light comfortable by reducing the direct glare of the light source. Clear toughened glass. LOR -- INSTALLATION AND MAINTENANCEThe tempered front glass diffuser is fixed externally to the fitting through silicon resin, perfectly flush with the front ring. Water and dirt deposits that can disturb the lighting performance of the projector can easily flow away. WIRINGSupply 5m cable section type FEP/FEP + PCP (Microstage and Ministage) or FLAT (Stage and Megastage) sealed with B component epoxy resin, wired internally protected by silicon sheaths. Isolation: CLASS II . Available colours: Aluminium grey (cod.14), Anthracite grey (cod.24). Weight: 1.73 Kg Glow Wire test: --LED circuit included.REGISTERED DESIGN MICROSTAGE BLADE OF LIGHT PATENTED, REGISTERED DESIGNThis luminaire contains built-in LED modules. In case of damage or malfunction please contact the manufacturer to receive additional instructions on how to replace and relative spare parts to order. The LED modules cannot be handled in the luminaire by the end user.LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), where uniformity and quality of the light is 70,000 hours referred to L80 B10 Ta 25 ° C (50,000 hours referable to L80 B10 Ta 40°C). Lifespan of the luminaire > 50,000 hours at 40°C. Performance Ambient temperature Tq 25°C. Operating ambient temperature range is from -20°C to +50°C. Storage temperature range from -20°C to +60°C.

No Rating

Product Version: Revit Architecture 2018

2319 Downloads