The BEECO Friendly Double Check Backflow Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1015, CSA B64.5 and IAPMO listed.

No Rating

Product Version: Unknown

308 Downloads

The BEECO Friendly Reduced Pressure Zone Backflow Preventer Valve is designed to stop the reverse of flow of a liquid into a potable water system. The proper installation of a backflow preventer must be done by a certified expert under local codes and guidelines to assure the protection of the drinking water system. The Valve shall be certified to ASSE 1013. Is Certified to cUPC and IAPMO listed.

No Rating

Product Version: Unknown

208 Downloads

Series LF800M4QT Lead-free* Anti-Siphon Pressure Vacuum Breakers prevent the reverse flow of liquids in a plumbing system due to backsiphonage where there is a potential health hazard. For use in continuous pressure applications where the water enters the equipment at or below its flood rim. Designed for ease of maintenance with a replaceable plastic seat and readily accessible test cocks for testing and winterization. The seat disc is silicone rubber for durability, and an O-ring bonnet seal resists fouling.

No Rating

Product Version: Revit MEP 2014

162 Downloads

Series RD-100-R epoxy coated cast iron overflow roof drain with flashing clamp with integral 2 in. (51mm) high external water dam, self-locking polyethylene dome (standard), and no hub (standard) outlet.

No Rating

Product Version: Revit Structure 2014

196 Downloads

Series RD-200-R epoxy coated cast iron overflow roof drain with flashing clamp with integral 2 in. (51mm) high external water dam, self locking polyethylene dome (standard), and no hub (standard) outlet.

No Rating

Product Version: Revit Structure 2014

127 Downloads

kit up your renderings with water fountains.materials listed under FOUNTAIN CENTER,RUNOVER,SPRAY and WATER

Product Version: Revit Architecture 2009

32246 Downloads

Series RD-300-R epoxy coated cast iron overflow roof drain with flashing clamp with integral 2 in H2199(51mm) high external water dam, self-locking polyethylene dome (standard), and no hub (standard) outlet.

No Rating

Product Version: Revit MEP 2014

132 Downloads

Series LFWCV, LFWCVS Lead Free* Brass Swing Check Valves prevent reverse fluid flow in water and steam applications. The Series features metal-to-metal seal with either threaded NPT or solder end connections in sizes 1/2 to 1 in. (15 to 25mm). They provide low pressure drop and automatic closure when fluid flow is stopped. Maximum Pressure: 200psi (13.8 bar) WOG (non-shock), 125psi (8.6 bar) WSP

No Rating

Product Version: Revit MEP 2014

718 Downloads

Series LFWCV, LFWCVS Lead Free* Brass Swing Check Valves prevent reverse fluid flow in water and steam applications. The Series features metal-to-metal seal with either threaded NPT or solder end connections in sizes 1/2 to 1 in. (15 to 25mm). They provide low pressure drop and automatic closure when fluid flow is stopped. Maximum Pressure: 200psi (13.8 bar) WOG (non-shock), 125psi (8.6 bar) WSP

No Rating

Product Version: Revit MEP 2014

517 Downloads

Under counter Basin with Fixing Accessories Set Size: 555x425x195 mm, Shape : Oval

 Vitreous china sanitary ware products are fragile in nature and need to be handled with care (to avoid personal injury) at all times during its storage, handling, installation and use thereafter.  The product is heavy and it is recommended that two persons hold it while it is being fixed.  Carefully inspect the new product for damage before installation.  Risk of product damage. Over tightening may cause breakage or chipping of vitreous china.  Risk of external leakage. Do not lift or rock the bowl after placement.  Always test your cleaning solution on an inconspicuous area on the product before applying it to the entire surface.  Do not allow cleaners to sit or soak on the product.  Use a soft, dampened sponge or cloth to clean. Never use abrasive material like a bristle brush or scouring pad.  Wipe surfaces clean and rinse completely with water immediately after applying cleaners.  Clean Chrome, stainless steel surfaces once a week. Do not use cleaners containing chloride on chrome, stainless steel. If used, rinse the surface immediately to prevent corrosion.  Wherever chrome plating is used on the products, use only warm water to clean and then dry with a soft cloth

No Rating

Product Version: Revit Architecture 2018

1439 Downloads

Under counter Basin with Fixing Accessories Set Size: 555x425x195 mm, Shape : Oval

 Vitreous china sanitary ware products are fragile in nature and need to be handled with care (to avoid personal injury) at all times during its storage, handling, installation and use thereafter.  The product is heavy and it is recommended that two persons hold it while it is being fixed.  Carefully inspect the new product for damage before installation.  Risk of product damage. Over tightening may cause breakage or chipping of vitreous china.  Risk of external leakage. Do not lift or rock the bowl after placement.  Always test your cleaning solution on an inconspicuous area on the product before applying it to the entire surface.  Do not allow cleaners to sit or soak on the product.  Use a soft, dampened sponge or cloth to clean. Never use abrasive material like a bristle brush or scouring pad.  Wipe surfaces clean and rinse completely with water immediately after applying cleaners.  Clean Chrome, stainless steel surfaces once a week. Do not use cleaners containing chloride on chrome, stainless steel. If used, rinse the surface immediately to prevent corrosion.  Wherever chrome plating is used on the products, use only warm water to clean and then dry with a soft cloth

No Rating

Product Version: Revit Architecture 2018

697 Downloads

No Rating

Product Version: Revit Architecture 2012

9704 Downloads

Series LF26A Lead Free* Small Pressure Regulators are used in small general purpose applications to regulate pressure in piping systems using water and No. 2 fuel oil. They have a Lead Free* brass body construction with NPT threaded female inlet and outlet connections, 1/4 in. two-way low-pressure gauge port, aluminum spring cage, Buna-N stainless steel disc, reinforced Buna-N diaphragm, and tee handle adjustment. Options include Viton trim and slotted adjusting screw. Strainers are recommended. Series LF26A has an oversized orifice and is ideal for use on beverage dispensing and paint spraying equipment, ice cube machines, humidifiers, drinking fountains, and other small process applications. Maximum Working Pressure: 300psi (21 bar).

No Rating

Product Version: Revit MEP 2014

190 Downloads

Series LF215 Super Sensitive Low Pressure Regulators are designed to meet low pressure precision requirements. The high ratio of diaphragm to orifice provides excellent performance and stability at low reduced pressure. The Series LF215 is ideally suited for water requirements up to 2.5 gpm (9.5 lpm) due to its Lead Free* brass body and brass and stainless steel internal parts. The LF215 is also suitable for pressure supply to wall attachment fluidic devices. The LF215 features Lead Free* construction to comply with Lead Free* installation requirements.

No Rating

Product Version: Revit MEP 2014

103 Downloads

Series LF263A Lead Free* Small Pressure Regulators are used in small general purpose applications to regulate pressure in piping systems using water and No. 2 fuel oil. They have a Lead Free* brass body construction with NPT threaded female inlet and outlet connections, 1/4 in. three-way low-pressure gauge port, aluminum spring cage, Buna-N stainless steel disc, reinforced Buna-N diaphragm, and tee handle adjustment. Options include Viton trim and slotted adjusting screw. Strainers are recommended. Series LF263A has an oversized orifice and is ideal for use on beverage dispensing and paint spraying equipment, ice cube machines, humidifiers, drinking fountains, and other small process applications. Maximum Working Pressure: 300psi (21 bar).

No Rating

Product Version: Revit MEP 2014

125 Downloads

Lap pool 75'2" long, 42' wide to accomodate 6 lanes. 9 foot deep-end, steeply slopes to 6 ' deep, then slowly slopes up to 3' deep shallow end. I've made the concrete walls for a pool of the above dimensions. Capped it with an Aluminum gutter. And filled the pool with the correct mass of water. Beware the water might not show up in your standard views becuase "mass" objects and families generally are hidden (thus you will need to tweak your visual settings, or unhide>category>mass). Also be sure to create your site around the pool extents, or excavate the necessary hole for placing the pool. If you simply put the pool on a pre-made site the site won't recognize the walls as retention and you will appear to have a pool full of dirt.

Product Version: Unknown

16224 Downloads

Lavadora extractora TSL-200 Braun, hospedada en pared, de paso a travez para uso hospitalario, para barrera sanitaria, para cuartos libres de contaminacion,  conexiones listas para vapor, agua fria y agua caliente, 90-105 kilogramos de capacidad

(Washer extractor TSL-200 Braun, hosted wall pass-travez for hospital use, for sanitary barrier for rooms free of contamination, lists connections for steam, hot water and cold water, capacity 90-105 kg ) 

Product Version: Revit MEP 2013

3937 Downloads

Pack of Open 3/4 900mm water/dry slide for playground or theme/water park.Consisting 30,45,60 degree slide.

No Rating

Product Version: Revit Architecture 2018

2323 Downloads

No Rating

Product Version: Unknown

2986 Downloads

stainless steel equipment for kitshen

No Rating

Product Version: Unknown

1620 Downloads

Product Version: Revit MEP 2013

1343 Downloads

Product Version: Revit Architecture 2011

2605 Downloads

Reference Model: Europa Noblesse Flex

Parametric materials.

Made entirely with Revit tools.

No Rating

Product Version: Revit Architecture 2019

330 Downloads

Fully editable wall based waterspout

Product Version: Unknown

3475 Downloads

Used for preparing hot drinks

No Rating

Product Version: Unknown

2307 Downloads

WATTS carrier ISCA-101   Adjusts for the toilet outlet ht and the 'X' dimension

No Rating

Product Version: Revit MEP 2010

1915 Downloads

No Rating

Product Version: Revit MEP 2013

1408 Downloads

CREDITS: Tom Lima

Just a updated version of his 2018 model

Without major details, only having pipe connections on both ends so it can be placed in any existing pipe.

No Rating

Product Version: Revit MEP 2020

198 Downloads

No Rating

Product Version: Revit Architecture 2014

2530 Downloads

Product Version: Unknown

1995 Downloads