 |
This is just a handmade north symbol, tracing over a cursive N letter and adding some fun to it.
You will have to manually rotate the symbol to your north orientation. |
|
Product Version: Revit Architecture 2012
4416 Downloads
|
|
 |
This is a plastic 20 oz water bottle.
Clear plastic with water inside.
White cap. No label. |
|
Product Version: Revit Architecture 2011
17878 Downloads
|
|
|
 |
Revit 2017
This is a closet unit with a central shelving system and rods on both sides, similar to the starter kit that ClosetMaid offers.
The central shelves are 17" total in width.
The shelves and rods on the sides are parametric.
You can adjust the length of the shelves, and if they are visible or not.
You can also decide if the 2 drawers on the unit are visible or not. |
|
Product Version: Unknown
16712 Downloads
|
|
|
 |
This is a detail component family to be used in sections and details.
Basis of design is Nystrom 3" Width Angle Nose. |
|
Product Version: Revit Architecture 2015
1298 Downloads
|
|
|
 |
There is a material for the fabric and also a material for the metal.
The height of the curtain can be adjusted on the base and also on the top.
The rod height is also adjustable, I think.
The curtain is stationary - you cannot close it.
The flanges can be adjusted away from the wall or set it to "0" to be flush with the wall. |
|
Product Version: Revit Architecture 2012
71892 Downloads
|
|
|
 |
You cannot change the sofa parameters. It is a 2 seats modern looking couch.
There are 2 pillows on it and you can turn them on or off.
You can assign one fabric for the couch.
You can assign one fabric for the pillows and one fabric for the trim at the edge of the pillows. A flat fabric works better, since it converges toward the middle.
It was created with Revit 12, but the version is not yet available at the drop down menu. |
|
Product Version: Revit Architecture 2011
8160 Downloads
|
|
|
 |
Insert as a DOOR!!
This is an expasion joint from wall to wall, mostly to be used with gypsum board walls.
The gap is 8". The plan represensation will show the joint gasket details. The elevation will show the trim and middle metal, as well as the 2 side expansion gadgets.
Both metal and expansion gadgets allow material selection.
This joint system is similar to InPro 233-A07 wall to wall expansion joint |
|
Product Version: Revit Architecture 2015
1760 Downloads
|
|
|
 |
Simple clothes hanger to use on closets.
It has a 3D and simbolic line representation.
Material for the body and metal.
|
|
Product Version: Revit Architecture 2013
15907 Downloads
|
|
|
 |
Linear wood fence.
The posts will space at around 5ft. There are 3 rails. The boards will space at around 6".
There is a parameter for material.
It cannot go up in an angle. |
|
Product Version: Revit Structure 2017
7699 Downloads
|
|
|
 |
This family is to be used in drafting view.
It is a side view of a brick tie, when attaching to a CMU wall.
You can adjust the brick tie to catch the difference between the CMU and brick course if needed. |
|
Product Version: Revit Architecture 2011
3023 Downloads
|
|
|
 |
This model is a face based model for the vertical plate. Both plates are in a diamond shape and there is a cable between them. There are 2 parameters - one adjust how far from the wall the bottom / horizontal plate is; the other adjusts how far below the vertical plate the bottom plate is. Stainless Steel Material. |
|
Product Version: Revit Architecture 2011
19389 Downloads
|
|
|
 |
You can adjust the height from the floor.
|
|
Product Version: Revit Architecture 2011
7273 Downloads
|
|
|
 |
Insert this spot elevation as a symbol and you will get the target, the line and 2 labels. The label above the line gives you an elevation in foot-inches. The label below the line gives you an elevation in engineer standards - 100.33' (example) This works great on site plans, when you have to give the real site dimension compared to the architectural dimension you chose. |
|
Product Version: Revit MEP 2009
9155 Downloads
|
|
|
 |
Bleacher sim. to Jaypro 4 Rows Tip and Roll Bleachers.
4 families to adjust length - 7 1/2 ft, 15 ft, 21 ft and 27 ft.
Adjust material for the planks and support. |
|
Product Version: Unknown
22622 Downloads
|
|
|
 |
This is a set of 4 patio umbrellas, 9 ft wide each, attached to a central pole. This central pole also has an umbrella on the top. You can change the height from the ground with a parameter. I also included a parameter for a fabric material. Once you insert in your drawing, you can add any fabric to the tops as you wish. The poles and supports are made out of aluminum. |
|
Product Version: Revit Architecture 2011
12114 Downloads
|
|
|
 |
There are several dimensions to choose from, begining at 24x24 up to 36x60.
The chairs adjust to the size of the table.
You can choose to have the end chairs or not.
The material can be adjusted.
The chairs came from a download from Revitcity.
|
|
Product Version: Revit Architecture 2014
58539 Downloads
|
|
|
 |
This is a generic model I made, similar to Simpson EPB44PHDG Elevated Post Bases. I did not include any adjustable parameter, but you can open the family and modify the location of the bolt and nut, treaded rod, etc. I could not find a Simpson Revit file, so I created this the best I could. Updated on Sep 10th, to fit 3 1/2" post. |
No Rating |
Product Version: Revit Architecture 2011
3235 Downloads
|
|
|
Search